Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Determine the specific volume of superheated water vapor at 15MPa and 350oC, using a) the ideal gas equation; b) the generalized compressibility chart; and c) the property table. 2. A 2 m3 tank containing nitrogen at 25oC and 500kPa is connected through a valve to another tank containing 3kg of nitrogen at 35oC and 200kPa. Now the valve is opened and the entire system is allowed to reach equilibrium at temperature of 20oC. Determine the volume of the second tank and the final equilibrium pressure. 3. A rigid tank contains an ideal gas at the absolute pressure of 200kPa and 227oC. The gas is cooled until the gage pressure reads 50kPa. If the atmospheric pressure is 100kPa, determine the final temperature of the gas. 4. Using the property tables (A-11, A-12, and A-13), find the properties of R-134a at the given conditions. T (oC) P (kPa) v (m3/kg) x phase - 30 Sat-L 800 Sat-V 10 0.8 Sat-mix 120 0.3 0 100 -20 450 10 0.049403 500 0.0008059 1000 0.01 5. ) Three kilograms of water in a container have a pressure of 100 kPa and temperature of 250°C. What is the volume of this container? 6. ) Two kilograms of water fills a 0.1 m3 rigid tank (the volume will not change) at an initial pressure of 2MPa. The container is then cooled to 40oC. Determine the initial temperature and final pressure. 7. Ten kilograms of water at saturated liquid phase fills in a piston-cylinder device (volume can change) at 50oC. The device is now heated until all the water transforms into saturated vapor phase at 100oC. Determine 1) the pressure and specific volume at the initial state; 2) the pressure and specific volume the final state; and 3) the total volume change.
a drill operation is to be performed with a 16 mm twist drill the hole is blind with a depth of 50 mm.cutting speed is
A heat pump with a COP (coefficient of performance) of 2.8 is used to heat an air-tight house. When running, the heat pump consumes 5 kW of power
Find the inside and outside diameter when the ratio of inside to outside diameters is 0.5.
find densities, enthalpies and efficiency for gas turbine power cycle with the following conditions.
Compare the time and cost of using the following three alternative methods for casting the concrete for the wall: 1) direct chute 2) pumped 3) crane and bucket.
a four-cylinder four-stroke 2.2 liter gasoline engine operates on the ideal otto cycle with a compression ratio of 10.
What load P allow can be supported at the midpoint of the bar if the yield stress in the steel wires is 220 MPa and in the aluminium wire is 80 MPa? A saftey factor of n = 2 is needed.
a construction crew lifts approximately 560 lb of material several times during a day from a flatbed truck to a 32 ft
problem 110degc water is flowing in a 10-mm diameter smooth tube. the mass flow rate of the water is 0.15 kgs. the
the final paper provides you with an opportunity to integrate and reflect on what you have learned during the class.the
what is the velocity of the cart when the bullet becomes embedded int he terget? during the firing, the man remains at the same position on the cart. neglect rolling resistance of the cart.
Product and Engineering Design Review
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd