Design truth table to approve or disapprove any transfusion

Assignment Help Electrical Engineering
Reference no: EM13267459

The objective of this problem is to design a truth table which will lead to a combinational logic circuit which will aid in the determination of the acceptability of emergency blood transfusions. It is known that human blood can be catecorized into four types: A, B, AB, and O. Persons with type A can donate to both A and AB types and can receive blood from both A and O types. Persons with type B blood can donate to both B and AB and can receive from both B and O types. Persons with AB blood can donate only to type AB, but can receive from any type. Persons with type O blood can donate to any type, but can receive only from type O. Choose type O to be binary 00, type A to be binary 01, type B to be binary 10, and AB to be binary 11. Design a truth table that will approve or disapprove any particular transfusion based on these conditions.

Reference no: EM13267459

Questions Cloud

Find the electron and hole concentrations-mobilities : Find the electron and hole concentrations, mobilities, and resistivities of silicon samples at 300K with an impurity concentration of (a) 5X10^15 boron atoms and (b) 2X10^16 boron atoms and a.5X10^16 arsenic atoms.
Calculate the basic and diluted eps for 2013 : Net Income: $1,200,000 & tax rate is 40%. Calculate the basic and diluted EPS for 2013. Are there any dilutions, if any, in this equity structure?
Explain the expected polarity of the indicated bonds : Use the ? - l?+ convention and the crossed arrow to show the direction of the expected polarity of the indicated bonds in the following compounds.
Find the current magnitude of the angular momentum of car : A 1590 kg car has just passed a diner. The closest the car came to the diner was R = 12.5 m, find the current magnitude of the angular momentum of the car about ther dinner
Design truth table to approve or disapprove any transfusion : The objective of this problem is to design a truth table which will lead to a combinational logic circuit which will aid in the determination of the acceptability of emergency blood transfusions. It is known that human blood can be catecorized int..
What is the annual lease payment : What is the annual lease payment? Provide the journal entry for 12/31/13 for Romeo.
Explain what is the density of concentrated sulfuric acid : When the same flask is filled with concentrated sulfuric acid, H2SO4, its mass is 1026.57 g. What is the density of concentrated sulfuric acid. Assume water has a density of 1.00 g/cm3 at the temperature of the measurement.
What is the purpuse of technical analysis : What is the purpuse of technical analysis, and why are those who use technical analysis referred to as chartists?
How are the filmmaker view of family expressed through films : How are the authors' and filmmaker' view of family expressed through these texts and films? what are examples of successful families in these works

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design a circuit that takes as input a single bcd digit

The 9s complement of a BCD digit can be used similarly to the way ones and twos complements of binary numbers are used preform subtraction via addition. The 9s complement of a BCD digit is simply the BCD coded result of subtracting the digit from ..

  Find the load voltage and power output realized

Design a suitable amplifier using a combination of these stages. Your design should utilize the minimum number of stages and should ensure that the signal level is not reduced below 10 mV at any point in the amplifier chain.

  Calculate the voltage drop across the diode

Express the diode current equation. A) Define all the diode parameters and draw the I-V characteristics. (Assume non-ideal diode) B) If IF=10 mA, Is=10-15A, VT=25mV, Calculate the voltage drop across the diode.

  What would be the current drawn by two bulbs

Consider the problem of using a low-voltage system to power a small cabin. Suppose a 12-V system powers a pair of 100-W lightbulbs (wired in parallel). a. What would be the (filament) resistance of a bulb designed to use 100 W when it receives 12 V

  What are the names of the three regions of the bipolar

What are the names of the three regions of the bipolar junction transistor? Why is there a thin region of one material type

  What was the height of the initial point it was released

an 8kg block is released from the rest on a frictionless incline of angle 60.if the speed of the box is 10m/s when it reaches to the ground what was the height of the initial point it was released

  What are the corresponding voltage-current and power gains

A buffer amplifier with a gain of 1 V/V has an input resistance of 1M and an output resistance of 10 ohm. It is connected between a 1-V, 100-k ohm source and a 100-ohm load. What load voltage results and what are the corresponding voltage, current,..

  Find the response time of the power meter in the data sheet

Through the data sheet the power meter is 4.5 HP. Find the hp range for PH-3A-HG in hp. The power meter measures the power and outputs a 0 - 10 voltage signal. Calculate the conversion factor for converting the voltage output

  How to convert binary to different number patterns

a)Describe the difference between a relay logic system and a PLC control system. Are there any advantages of PLC control system over relay system. Explain the advantages in details with one example.

  Write a short sequence of instructions to perform the task

Suppose you are given the following task: "Find the smallest (in the signed sense) of a sequence of 100 8-bit values stored in sequential file register locations starting at file register 800." Write a short sequence of instructions to perform thi..

  Explain why there is a decrease in output voltage

In a voltage stabilizer circuit with a Zener diode, the output voltage decreases when touching the zener diode with your fingers when no load is connected. Ideally, the output voltage should not drop. Explain why there is a decrease in output volt..

  Design a combinational circuit with four inputs

Design a combinational circuit with four inputs, x,y,w, and z, and four outputs: A, B, C, and D. When the binary input value in decimal is 3,8,12 or 15, the binary output value is one less than the input value, otherwise it is one greater than the..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd