Design the flexural reinforcement for this member

Assignment Help Civil Engineering
Reference no: EM13563764

A rectangular concrete beam of width b = 24 inches is limited by architectual considerations to a maximum total depth of h = 16 inches. it must carry a total factored load moment of Mu = 400 ft-kips. Design the flexural reinforcement for this member, using compression steel if necessary. Allow 3 inches to center of the bars from the compression or tension face of the beam. Materal strengths are Fy = 60,000 psi and F'c = 4,00 psi. Select Reinforcement to provide the needed areas , and show a sketch of yuor final design, including provision for no.4 stirrups.   

Reference no: EM13563764

Questions Cloud

What percent removal efficiency may be expected under : A cyclone separator is being used to remove particulates from a gas stream. The current removal efficiency is 96% for an air flow rate through the separator equal to 18 m3/s. Due to a process change, the air flow rate is expected to increase to 22 m3..
Calculate a value of temperature that could be used : A correlation for particulate removal efficiency in an electrostatic precipitator (n) as a function of gas velocity (u) may be written in the form: n = 1 - e^-k / u.
Determine the proportional limit stress the modulus : At the proportional limit, a 32-mm-thick by 87-mm-wide bar elongates 10.2 mm under an axial load of 532 kN. The bar is 2.4 m long. Poisson%u2019s ratio, , for the material is 0.27.
Can one collector be temporarily taken out of service by : Dust is removed from the airstream of a municipal incinerator by four dust collectors operating in parallel, each handling 1/4 of the total airflow of 200 m3/min. The airstream contains 10 g/m3
Design the flexural reinforcement for this member : A rectangular concrete beam of width b = 24 inches is limited by architectual considerations to a maximum total depth of h = 16 inches. it must carry a total factored load moment of Mu = 400 ft-kips. Design the flexural reinforcement for this member,..
Calculate the emissions of sulfur dioxide : Calculate the emissions of sulfur dioxide, particulates (fly ash), and carbon dioxide per kilowatt-hour of electrical energy produced. Assume that all of the carbon in the coal is released to the atmosphere.
What is the second year book value for equipment with : What is the second year book value for equipment with an initial cost of $11,000, a salvage value of 1,000 and a recovery period of 5 yrs for A. straight line depreciation. B. Double declining balance. C. MACRS?
What are the adjusted elevations for benchmarks b c and d : Differential leveling between benchmarks A,B,C,D, and A gives elevation differences(m) of -15.632, 32.458, 38.214, and -55.025, and distances(km) of 4,6,5, and 3 respectively.
What nominal annual interest rate effective annual interest : A store charges 1.25 % interest per month in credit purchases. This is equivalent to: what nominal annual interest rate, effective annual interest rate, and effective monthly interest rate?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the maximum external pull in each of the 4 gears

If a tractor with 23-hp, a max speed of 3.6 mph in 1st gear and an effieiciency of 92% is operated operated down a 4% slope and the rolling resistance is 80 lb/ton, what is the maximum external pull in each of the 4 gears.

  Describe the construction and beneficial features of switch

An inductive proximity switch is a device used in valve feedback, describe the construction, operating principle and beneficial features of the switch

  Estimate the elastic shrinkage,and total axial deformation

Estimate the elastic, shrinkage, and total axial deformation of a concrete column after 2 years of permanent load application.  Assume the full structural load was applied at 28 days after placing concrete.

  Three cylinders from the same mix were tested

Three cylinders from the same mix were tested for strenght.  Cylinders A and B were cast in 4x8 molds while cylinder C was cast in a 6x12 mold.  The total loads were as follows; cylinder A= 65,200 lbs.,  cylinder B= 68,550 lbs., cylinder C= 151,190 l..

  Determine the cartesian coordinates of the anchor

A fisherperson, pulling on the anchor cord, causes a force on the man of F=(40i+20j-50k)N. If the cord is 30m long,determine the Cartesian coordinates of the anchor at A. Assume that cord OA is a straight line.

  A hydraulic jump occurs at the entrance of this channel

A hydraulic jump occurs at the entrance of this channel, with a downstream depth equal to the uniform flow depth. What is the upstream depth, y1, of the hydraulic jump?

  Calculate the forces exerted by the water on the bend

Water flows through a horizotal 45 deg reducing bend with a 36 inch. diameter upstream and a 24 inch diameter downstream, at the rate of 20 cfs under a pressure of 15 psi at the upstream end of the bend. Neglecting head loss in the bend, calculate..

  Calculate volume of sample that will be used in bod bottle

If a sample for BOD needs to be diluted by a factor of 0.02 , calculate the volume of sample that will be used in the BOD bottle

  What is the minimum perimeter of that the blade must have

A rectangular blade weighing 0.02 lbf is kept in the surface of water (sigma=0.073 N/m) solely by surface tension forces. What is the minimum perimeter of that the blade must have so that this is possible

  What is chemical name of first hazardous air pollutant

What is the chemical name of the first hazardous air pollutant under Title III regarding the Clean Air Act

  Change in it internal energy

A gas is compressed at a constant pressure of 0.800 atm from 9.00L tp 2.00L. in the process, 400J of energy leave the gas by heat. (a) What is the work done on the gas? (b) What is the change in it internal energy?

  Determine the gravitational force acting between two spheres

Determine the gravitational force acting between two spheres that are touching each other. The mass of each sphere is 400 kg and the radius is 300mm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd