Design size of smoke vents in the ceiling with the objective

Assignment Help Civil Engineering
Reference no: EM13300273

A storage room in an industry has a floor area of 30 m by 50 m and a height of 10 m. A garage door has a width of 3 m and a height of 3 m and the room has four windows that are 0.9 m by 0.9 m, situated at the height of 1 m from the floor. the fire load consists mainly of wooden pallents (1.2 x 1.2 m^2); the maximum amount stored is two pallet loads, side by side, which are 1.4 m high. the fire is assumed to attain maximum effect after 6 mnutes and firefrighters are assumed to arrived at the location 15 minutes after the fire starts. Design the size of smoke vents in the ceiling with the objective of avoiding falshover and only allowing the smoke layer to be 3 m thick. Assume a flow coefficient of 0.6 for the ceiling vents and assume the walls and ceiling to be of steel sheet, isolaed with mineral wool with kpc-3.3 * 10^3 W^2s/m^4K^2

Reference no: EM13300273

Questions Cloud

Why do we focus on cash flows rather than net income : Why do we focus on cash flows rather than net income in capital budgeting? Is operating cash flow the same as EBITDA (Earnings before interest taxes, depreciation and amortization)?
What is the fractional change in length : Most materials will expand when the temperature is increased. The change in size will depend on several factors, including the original size, What is the fractional change in length
Wedding planning issued : Bridezilla Wedding Planning issued two checks totaling $150,000 to BabyCakes Bakery for wedding cakes it had purchased. BabyCakes Bakery endorsed the checks over to the law firm of Shark & Shyster as payment for a retainer.
What are the relevant factors in the decision : What are the relevant factors in the decision and which alternative is in the best interest of the company over the next two years? Show your calculations.
Design size of smoke vents in the ceiling with the objective : A storage room in an industry has a floor area of 30 m by 50 m and a height of 10 m. A garage door has a width of 3 m and a height of 3 m and the room has four windows that are 0.9 m by 0.9 m, situated at the height of 1 m from the floor.
What is the average density of the statue : A 2000 kg statue falls into a circular jacuzzi with a diameter of 5 m, What is the average density of the statue
What must the beta be for the other stock in your portfolio : You own a portfolio equally invested in a risk-free asset and two stocks. if one of the stocks has a beta of 1.05, and the total portfolio is exactly as risky as the market, what must the beta be for the other stock in your portfolio?
Determine the mass of the bar : When 4425 J of heat are added to a 0.16-m-long silver bar, What is the mass of the bar
Calculate the time till the smoke layer is from the floor : A room has a floor area of 500 m^2 and a height of 4 m. THe room is involved in a fire with a constant energy release rate of 1 MW. calculate the time till the smoke layer is 1.5 m from the floor for (a) the case where the leakage areas are at the ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate max torque that can be carried by hollow section

Assume a cross-sectional medial length of 32 in. (no stretching of the sheet due to bending). If the maximum shear stress must be limited to 19 ksi, determine the maximum torque that can be carried by the hollow section

  Explain how to compute the disclosure and elevation of a

Reciprocal leveling gives the following readings in feet from a setup near A: on A, 2.071; on B, 8.254, 8.259 and 8.257. At the setup near B: on B, 9.112; on A, 2.926, 2.930 and 2.927. The elevation of B is 1099.600. Compute the disclosure and ele..

  Plot ground level concentration of sulfur dioxide as functn

Plot the ground level concentration of sulfur dioxide as a function of distance from the stack and determine the maximum ground level concentration at both with and without air pollution control and the distance from the stack where the maximum co..

  Find the lateral area of the frustum

a regular hexagonal pyramid has an upper base edge of 16 ft. and a lower base edge of 28 ft. if the volume of the frustum is 18041 ft^3., find the lateral area of the frustum.

  Determine the maximum safe load for the column

A finished 2 x 4 timber (actual size 1 5/8 in. x 3 1/2 in. x 10 ft long) is used as a fixed-end, fixed-end column. If the modulus of elasticity for the timber is 1600 ksi and a factor of safety of 3 with respect to failure by buckling is specified

  Find what is the upward acceleration starting from rest

An elevator weigh 4000kg. When the upward tension in the supporting cable is 48000N what is the upward acceleration Starting from rest, how far does it rise in 3s

  Magnitudes of the additional loads

Determine the magnitudes of the additional loads that must be applied at B and F if the resultant of all six loads is to pass through the center of the mat.

  Estimate the plume mass flow rate of a pool of benzene

A pool of benzene is ignited on the floor of a large industrial building. The total area covered by the Kerosene pool is 6 meters square (Note that this is considered a large pool D>0.2 meters). Combustion efficiency is 70%. Estimate the plume mas..

  Find the density of air and weight of the air in the tank

An empty air tank has a volume of 0.024 m3. The compressor on the tank is run until the pressure gauge reads about 65 psi (or 22,500 Pa). Assuming the temperature of the tank is 25 C, find the density of the air and the weight of the air in the ta..

  Design condition inflow and pumping rates

Derive an equation that allows you to compute the diameter of the drain hole for a desired steady water height in the tank for the design condition inflow and pumping rates.

  Total vehicle delay in the cycle with queueing diagram

If the queue clears exactly at the end of the effective green D/D/1 queuing applies, determine the total vehicle delay in the cycle (in veh-sec) .

  Calculate the maximum design load on a hollow aisi

Calculate the (maximum) design load on a hollow AISI 1020 steel shaft with an outside diameter of 2.5 inches and an inside diameter of 2 inches. Assume a safety factor of 2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd