Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A preliminary design on the use of a cantilever prismatic timber beam indicated that a beam with a rectangular cross section 2 in. wide and 10 in. deep would be required to safely support the load shown in part a of the figure. It was then decided to replace that beam with a built-up beam obtained by gluing together, as shown in part b of the figure, five pieces of the same timber as the original beam and of 2 X 2-in. cross section. Determine the respective lengths l1 and l2 of the two inner and outer pieces of timber that will yield the same factor of safety as the original design.
a number of students are answering a questionnaire form that has 55 questions. answer to each question is given as an
Design an two or three stage amplifier that :Operates from single supply of no more than +10 V, and consumes no more than 10 mA. Has an RIn = 50 Ohms w/in 10%. Has an ROut less than or equal to 1kOhms.
The state of a 9-bit register is 111011010. What is its content if it represents(a) Three decimal digits in BCD?(b) Three decimal digits in the excess-3 code?(c) Three decimal digits in the 84-2-1 code?(d) A decimal number?
1. Consider the block diagram below of a simple AM radio. Develop the Matlab code to simulate this system where: X(t) is a rectangle (square wave) signal with 5 cycles with a period of 12 W(t) is a low pass filter with an impulse response h(t) = e"..
An electronic timer consists of a resistor whose value is 10,000 ohms, a capacitor of 30 pico farads, and a 10 volt source which is applied across the RC connection at time t =0.
Store the arrival times in memory locations starting from $1000.(Do this is in C. Store the results in an array and don't worry about the speci c location of the results.)
Measurements on sodium have provided the following data: resistivity 4.7 ×10-8ohm m, Hall coefficient -2.5 × 10-10m3C-1, critical wavelength of transparency 210 nm, and density 971 kg m-3. Calculate (i) the density of electrons, (ii) the mobility, ..
Combine the following expressions into a single sinusoid and plot both the combined and original expressions in Matlab across 2 periods. a) 2cos(3t)-cos(3t-pi/4) b) sin(2t- pi/4) + 2cos(2t-pi/3) c) cos(t) - sin(t) d) 10cos((pi*t) + pi/3) + 8cos((p..
A 10 kVA transformer has an iron loss of 250 watts and a half-load copper loss of 80 watts. Determine the full-load efficiency at 0.8 power factor.
What characteristics of CMOS devices make them a desirable digital logic technology to use in portable electronic devices, such as MP3 players What device properties influence the operating speed and utility in portable electronic devices
A series RLC circuit is connected to a voltage source x(t). The output y(t) is taken across the capacitor. The negative side of x(t) and y(t) is the common ground. The values of the elements are: R=8.1250 Ohms, C= 1 farad, and L= 1.0 Henry.
If the MOD-8 binary counter is driven by a 10 MHz input clock with a 5% duty cycle, what is the output frequency and duty cycle of the final stage
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd