Design of a shallow foundation

Assignment Help Mechanical Engineering
Reference no: EM13947796

Following are the standard penetration numbers determined from a sandy soil in the field:

Depth (ft)

Unit weight of soil (lb/ft2)

N60

10

106

7

15

106

9

20

106

11

25

118

16

30

118

18

35

118

20

40

118

22

Using Eq. (3.30), determine the variation of the peak soil friction angle, f9. Estimate an average value of f9 for the design of a shallow foundation. (Note:  For  depth greater than 20 ft, the unit weight of soil is 118 lb/ft3.)

Reference no: EM13947796

Questions Cloud

What the video is speaking about in your own words : Watch the YouTube video " Assistive Technology: Opening Doors to Independence" and tell what the video is speaking about in your own words and your thoughts on the video
Estimate average relative density of sand : Assume the uniformity coefficient sCud of the sand to be 2.8 and an overconsolidation ratio (OCR) of 2. Estimate the average relative density of the sand between the depth of 3 to 6 m. Use Eq. (3.21).
Write differences between podcasts and streaming media : What are the differences between podcasts and streaming media
Cause companies to better market their products and services : Should there be an increase in regulation enacted to cause companies to better market their products and services? Why or why not? Provide an example to support your response.
Design of a shallow foundation : Using Eq. (3.30), determine the variation of the peak soil friction angle, f9. Estimate an average value of f9 for the design of a shallow foundation. (Note:  For  depth greater than 20 ft, the unit weight of soil is 118 lb/ft3.)
Why do you think standard costing is the most widely used : Accuracy of calculations and use of electronic worksheet formulas - Quality of written report and descriptive materials (and referencing) - Why do you think standard costing is the most widely used costing system in the world in manufacturing firms,..
Dives off of a raft - what happens to the diver : A tennis racquet hits a tennis ball. Why doesn't the racquet swing backwards when the ball hits it? (Shouldn't it swing back because of action-reaction forces?)
Discuss your own perception of students with an id : Identify at least two appropriate classroom instruction accommodations for students with an ID and explain their relevance. Use outside resources or websites in order to find the information, and cite them within your response. Discuss your own pe..
The company refused to pay, contending that the employees : The company refused to pay, contending that the employees were at-will and there was no enforceable contract, the alleged agreement was illusory and, in any case, it violated the statute of frauds because it took more than one year to come into effec..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assume constant gravitational acceleration

A rocket is launched vertically and reaches its maximum height hmax. What are its velocity, v(t)= (dh/dt) , and height above ground h(t) as a function of time t >_ 0(greater than or equal to) before it lands on ground (h = 0)?

  What flow will be expected if gate valve is one-half open

The entrance is inward projecting. What flow will be expected if the gate valve is one-half open?

  Determine the minimum diameter of a solid shaft

Determine the minimum diameter of a solid shaft used to transmit 500 kW of power from a 3000-rpm motor so that the shear stress does not exceed 50 MPa.

  Two large water reservoirs are connected by 8000 ft of

two large water reservoirs are connected by 8000 ft of schedule 40 steel pipe. the level of one reservoir is 500 ft

  Compute the heat transfer between the two locations

At a section where the diameter is 4 in, methane flows with the veloctiy of 50ft/s and a pressure of 85 psia. At a downstream section, where the diameter has increased to 6 in, the pressure is 45 psia. Assuming the flow to be isothermal, compute the ..

  Nitrogen initially occupying 35 ft3 at 87 psia 480degf

nitrogen initially occupying 3.5 ft3 at 87 psia 480degf undergoes in internally reversible expansion during which pv1.2

  Paint plant air house

Electricity might be used to run the fan to draw air through the system, and also to run a chiller - What is a typical COP for a commercial chiller?

  Assignment 1problem 1determine the analytical solution for

assignment 1problem 1determine the analytical solution for the maximum stress of the beam shown compare with stress

  Material a has a fracture toughness and yield stress ten

material a has a fracture toughness and yield stress ten times that of material b a write an expression for the

  A piston-cylinder device initially contains 007 m3 of

a piston-cylinder device initially contains 0.07 m3 of nitrogen gas at 130 kpa and 120 oc. the nitrogen is now expanded

  Oil has a specific gravity

Oil flows at a rate of 12gpm from a vented tank (pressure at point 1 is zero) through 1 inch inner diameter pipes and elbows, and through a pump and motor as shown. The pump adds HHPp= 3hp to and the motor extracts HHPm= 1hp from the fluid power.

  Find the displacement, velocity and acceleration

For each configuration shown in table 1, determine the angular displacements, angular velocities and angular accelerations of links 3 and 4 graphically and analytically . Use the Excel sheet discussed in the lecture to help you do the analytical s..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd