Design logic circuit to control electrical power to engine

Assignment Help Electrical Engineering

Reference no: EM13288461

Design a logic circuit to control electrical power to the engineignition of a speed boat. Logic output I is to becomehigh if ignition power is to be applied and is to remain lowotherwise. Gasoline fumes in the engine compartment present aserious hazard of explosion. A sensor provides a logic inputF that is high if fumes are present. Ignition power shouldnot be applied while the outdrive is in gear. Logic signalG is high if the outdrive is in gear and is low otherwise.A blower is provided to clear fumes from the engine compartment andis to be operated for five minutes before applying ignition power.Logic signal B becomes high after the blower has been inoperation for five minutes. Finally, an emergency override signalE is provided so that the operator can choose to applyignition power even if the blower has not operated for five minutesand if the outdrive is in gear, but not if gasoline fumes arepresent. a. Prepare a truth table listing allcombinations of the input signals B, E, F, G. Also, showthe desired value of I for each row in he table.b. Using the sum of products approach, write aBoolean expression for I. c. Using theproduct of sums approach, write a Boolean expression forI. d. Try to manipulate the expressionsof parts (b) and (c) to obtain a logic circuit having the leastnumber of gates and inverters. Use AND gates, OR gates and inverters.

Reference no: EM13288461

Questions Cloud

Define and write a balanced equation for the reaction : Write a balanced equation for this reaction. How many grams of iron are required to make 2.50 L of aqueous solution containing 8.00 % Iron (III) chloride by mass. The density of the solution is 1.067g/mL

Determine the maximum number of hopping frequencies : An FH-BPSK signal modulated with 6kbps data has a spectrum bandwidth of 20 MHz. the BPSK signal is filtered allowing only two spectral components on either side of the carrier find the maximum number of hopping frequencies.

What clock code is required and what is first null bandwidth : A DS-SS system requires 40 db of CW rejection of an interfering signal. it uses an 8-stage shift register m-sequence generator and transmits 1.5 kbps binary message data an a 2 GHz carrier. What clock code is required and what is the first null ba..

Determine what step should the code be set to : A spread spectrum system has a code rate that can be switched from 500 kbps to 1.5 Mbps in 100 k steps. If the message rate is 1.3 kbps and the processing gain is 1050. What step should the code be set to

Design logic circuit to control electrical power to engine : Design a logic circuit to control electrical power to the engine ignition of a speed boat. Logic output I is to becomehigh if ignition power is to be applied and is to remain lowotherwise. Gasoline fumes in the engine compartment present aserious ..

Explain wedge-and-dash bonds for the substituent groups : Use wedge-and-dash bonds for the substituent groups, and be sure that they are drawn on the outside of the ring, adjacent to each other

Determine the normalized impedance from the load : Determine the normalized impedance at λ/8 from the load if (a) its normalized impedance is 2 +j, (b) its normalized admittance is 0.2 - j0.5, (c) the reflection coefficient at load is0.3 + j0.4.

What will one share of b&k common stock be worth : The company adheres to a constant rate of growth dividend policy. What will one share of B&K common stock be worth 10 years from now if the applicable discount rate is 9 percent?

Find current i flowing in bar and resistance of the wire : A cylindrical wire of silicon has a radius of 1 mm and a length of8 cm. If a voltage of 5V is applied between the ends of the bar andμe = .11 m2/Vs, μh = .04m2/Vs, Ne = 1020electrons/m3 and Nh=Ne find the following

User Account

All Pages