Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
the hd cable signal send out is usually ranging between (1-25mv), with the frequency range from 1000Hz- 20Khz. An amplifier will gain 46 db will boost the signal before sending it through the cable connection. Signal will travel through 2 cable segments, each will deteroriate the signal by 1/100. To maintain the signal level, at the end of each cable segment a repeater was placed with gain + 20 db. Arriving at the location, signal is then splits to 20 houses which cause 60 db deteroriation. Calculate and design the appropriate amplifier needed to maintain the signal (max) 5V at the house.
An amplifier output is being evaluated by a technician. The output is found to be a sine wave. The measured time lapse from one sine-wave peak to the next is 5 milliseconds.
A 345-kV, 3-phase transmission line delivers 100 MVA, 0.866 lagging, to a DELTA connected load. Calculate the following: a.) The total real and reactive power delivered to the load. b.) The real and reactive power per phase.
For an RC circuit with a time constant of 1.0ms and assuming switch was closed at t=0, i) What is the time for the voltage across resistor to equal 10% of its initial value ii) What is the time for the voltage acro..
Locate and specify an appropriate sensor if it is to operate at 120 vac as an input to a PLC. Create the ladder diagram program to accomplish the specified control.
A temperature sensor has a static transfer function of 0.15mV/degrees C and a time constant of 3.3 s. If a step change of 22 degress C to 50 degress C is applied at t = 0, find the output voltages at 0.5s, 2.0s, 3.3 s, and 9s.
Moore sequential circuit, A Moore sequential circuit has one input and one output.The output goes to 1 when the input sequence 111 has occurred and the output goes to 0 if the input sequence
Design by direct implementation the electronic circuits for equations as the following logic equations using any real 1, 2, or 3 input logic gates. Assume all signals are high true (positive logic) and do not simplify the equations.
a) Design a band-pass filter consisting of an RC high-pass filter with a cutoff frequency of 300 Hz and an RC low-pass filter with a cutoff frequency of 3400 Hz. Carefully select R and C of each filter so that one filter does not load the other
(1) After writing the equations for mesh analysis, what parameters will be calculated How can the results be used to determine the branch currents (2) When working with Thevenin's, list the steps for solving for Vth and Rth.
A manufacturing plant has a 600V, 60Hz supply and the following loads: Lights: 24kW Electric furnace: 4.8 + j6.4%u03A9 with a current of 150A Motor loads, 160kW at 0.8 Power Factor, lagging.
a 2.0-kg block is moving right at 1.0 m/s just before it strikes and sticks to a 1.0-kg block iniially at rest. what is the total momentum of the wo blocks after the collision
write an 8051 program that would generate a 200khz, 50% duty cycle, square wave at P1.0.Use Timer 0 for the delay. Ignore the overheads cycles due to the instructions in the loop. Assume 12 MHz clock. All data must be hex.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd