Design and operate a vehicle in modern team-base environment

Assignment Help Mechanical Engineering
Reference no: EM13779630

Design Project Description

OBJECTIVES:

Conceive, Design, Implement, Operate a vehicle in modern team-based environment. The vehicle will be powered solely by the energy of one standard-sized mouse trap, (1 3/4" X 3 7/8"), and will enter a two-event competition:

1) traveling the longest linear distance, and 2) traveling a 5-meter linear distance in the shortest amount of time.

KEY MILESTONES:

•  Team Contract and Biography

• Team Project Management Plan

• FRDPARRC Sheet

• Paper-copy of Team Presentation

• Contest

• Team Presentations

DEFITIONS AND REGULATIONS :

By definition, a vehicle is a device with wheels or runners used to carry something, (e.g., car, bus, bicycle or sled). Therefore, launching a ball, (e.g., marble) from the mousetrap will be ruled illegal.

1. The device must be powered by a single Victor brand mouse trap (1 3/4" X 3 7/8") .

2. The mousetrap can not be physically altered except for the following: 4 holes can be drilled only to mount the mousetrap to the frame and a mousetrap's spring can be removed only to adjust the length of the its lever arm.

3. The device cannot have any additional potential or kinetic energy at the start other than what can be stored in the mousetrap's spring itself. (This also means that you cannot push start your vehicle.)

4. The spring from the mousetrap cannot be altered or heat treated.

5. The spring cannot be wound more than its normal travel distance or 180 degrees.

6. Vehicles must be self-starting. Vehicles may not receive a push in the forward direction or side direction.

7. The vehicle must steer itself. Measurements of distance will not measure the total distance traveled only the displacement distance.

8. Distance will be measured from the front of the tape at the starting line to the point of the vehicle that was closest to the start line at the time of release.

9. In its fully extended form, the vehicle must fit inside a 8" x 14 " x 8" box.

10. The instructor has the final decision as to the appropriateness of any additional items that might be used in the construction of the racer.

RUNNING THE CONTEST:

1. The race track is the hallway floor outside the classroom.

2. Each team contestant will be given three attempts for the speed event and the distance event. The winner will be the team with the highest winning index, which has this formula: winning index = (best time of the class/your best time of the three attempts) + (your longest distance of the three attempts/longest distance of the class). Any ties will be decided by a single run off between the racers which tied.

Attachment:- Mouse Trap Car Project.rar

Reference no: EM13779630

Questions Cloud

Compose an objective statement for a career path : Compose an Objective Statement for a career path that can be used on a resume. In addition, compose a short piece explaining where you want to end up in your first position after graduation. This piece should contain
Improper folding of the hemoglobin protein : How does the structural difference between valine and glutamic lead to the improper folding of the hemoglobin protein?
The organization''s perspective issues : How were you recruited for each position (or how is the typical employee recruited)?
Autonomic component of an emotional response functions : The proposition that facial expressions of emotion are innate is supported by the observation that blind children show different facial emotional expressions than do sighted persons.
Design and operate a vehicle in modern team-base environment : Conceive, Design, Implement, Operate a vehicle in modern team-based environment. The vehicle will be powered solely by the energy of one standard-sized mouse trap and will enter a two-event competition
Describe the reasons for disney''s adoption of itil : Describe the reasons for Disney's adoption of ITIL. Examine the results that were attained by Disney.
What will be the likely disposition of the case : For two months, Mark uses the lawn mower more than anyone. But then Johnny fails to make payments and the salesman sues Mark under the oral contract. What will be the likely disposition of the case
Selection and staffing issues : How do you think this would affect the organization's ability to attract the best employees?
The elasticity of demand coefficient for a good is 4 : If the elasticity of demand coefficient for a good is 4(in absolute term), we know: a: that for every 1%increase in quantity, there will be a 4% increase in price b: that for every 1% increase in quantity, there will be a 4% decrease in price c: that..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd