User Account

All Pages

Design and CFD Simulation of a Battery Module

Assignment Help Mechanical Engineering
Reference no: EM132392931

Advanced Flow Modelling Assignment -

Find - Design and CFD Simulation of a Battery Module for a Hybrid Electric Vehicle Battery Pac.

Procedure and discussion points:

1. Create the computational geometry in DesignModeler/ Solidwroks/any CAD software with the mentioned dimensions.

2. Build an appropriate mesh for the model and perform a grid refinement study.

3. Using the converged grid, check the iterative convergence.

4. Draw the Velocity contour at different selected planes of your model and discuss your results.

5. Draw the pressure contour at different selected planes of your model and discuss your results.

6. Plot the temperature profile along a selected line from inlet to outlet and discuss.

7. Draw the wall shear stress and discuss.

8. Plot the axial velocity profile at any selected position of your model and discuss.

9. Draw the Velocity vectors at different selected planes of your model and discuss your results.

10. Calculate the drag and lift coefficient and discuss (if applicable).

11. Calculate the deposition efficiency/deposition fraction and discuss (if applicable).

12. Draw the particle trajectories for different flow rates and discuss (if applicable).

13. Calculate the heat transfer coefficients (if applicable).

14. Calculate the Nusselt number from the following correlation and discuss (if applicable);

NuD = 0.023Re4/5DPrn

15. Connect your results with the existing literature.

[Deposition Efficiency = (number of injected particle/number of trapped particle) x 100

Submission: A written report is to be submitted including a short introduction and conclusion (one page long for each). The report should contain a discussion of the points above with evidence to support the discussion together with relevant figures such as figures illustrating the mesh or element distribution, plots of the velocity profiles, contour plots, etc.

Reference no: EM132392931

Questions Cloud

What was your impression of the pay surveys : What was your impression of the pay surveys you were able to access? If you were a compensation manager trying to price these positions, would the information.
Define what is meant by risk management : A human resource professional, as we have learned, has many disparate duties and responsibilities. One of the duties that is increasing in its importance.
How you would address the aspect you have selected : Propose how you, as the head of a U.S.-based multinational organization, would address the aspect you have selected as part of the TPP.
Identify the strengths of the organization structure : Identify the strengths of the organization's structure. (internal). Identify the weaknesses of the organization's structure. (internal)
Design and CFD Simulation of a Battery Module : Advanced Flow Modelling Assignment - Find - Design and CFD Simulation of a Battery Module for a Hybrid Electric Vehicle Battery Pac
Identify and explain the three primary hr activities : Identify and explain the three primary HR activities. Which activity do you think is most challenging and why? Requirements: Your answers should be thoughtful.
Benchmark - Ecclesiological Models : Assignment - Benchmark - Ecclesiological Models. Contrast the major models of the church in light of biblically faithful ecclesiology
Explaining how the topic is of interest to you : Write a paragraph (4-6 sentences) explaining how this topic is of interest to you and what you hope to gain from this course. Please post your discussion below.
Discuss the social impact of policies : Assignment - Understanding Public Policy. Discuss the social impact of policies. Discuss the limitations policies have on government power

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the maximum theoretical power that can be

steam at mpa 500 degrees c enters an insulted turbine operating at steady state with a mass flow rate of 7 kgs and

  Develop the titration curve in spreadsheet format

If 25 mL of 0.025 M Na2SO4 is titrated with 0.040 M Pb(NO3)2, develop the titration curve in spreadsheet format and plot the limiting current versus the volume of titrant.

  Small sphere with mass

A small sphere with mass 5.00.×10?7kg and charge +3.00?C is released from rest a distance of 0.550m above a large horizontal insulating sheet of charge that has uniform surface charge density ?=+8.00pC/m2.

  Load of chemicals hits the front edge of the fire

You are a pilot of a plane fighting a forest fire, you are flying 1000ft above the ground at a speed of 90 miles per hour and are going to drop a 5000 pound load of fire suppressing chemicals onto the fire, how far from the front line of the fire mus..

  What is the annual cost associated with supplying hot water

what is the annual energy consumption associ- ated with heating the water to a storage temperature of 55°C? For a unit electrical power cost of $0.18/kW · h

  An air-standard otto cycle has a compression ratio of 8 and

an air-standard otto cycle has a compression ratio of 8 and the temperature and pressure at the beginning of the

  If the compression is done reversibly compute the heat and

ammonia is to be isothermally compressed in a specially designed flow turbine from 1 atm and 672 r to 50 atm. if the

  Determine the maximum acceleration which may be measured

Determine the maximum acceleration which may be measured with the instrument and the uncertainty resulting from the displacement measurement.

  Perpendicular to the centroidal axis of the column

Assume E=31 ,000 MPa and ν=0.2 εa=-222x10-6 , εb=-213x10-6 , εc=45x10-6 Where gauges a, b and c are in line with, at 450 to and perpendicular to the centroidal axis of the column, respectively.

  Calculate the geometric scale ratio and the scale model

Calculate the geometric scale ratio and the scale model rotational speed - compute the power supplied per unit mass flow, the change in rothalpy

  Find the acceleration of the block of mass m up the plane

The blocks are connected by a light inextensible string that passes over a light frictionless pulley. Find the acceleration of the block of mass m up the plane, and deduce the tension in the string.

  Estimate work done by heart to keep the blood circulating

Estimate the work done by the heart to keep the blood circulating. The fluid that flows through the heart has a uniform velocity profile. The system can be modeled as steady-state with one inlet and one outlet. Neglect frictional loses in the pumping..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd