Design an integrator with an input resistance of 1m?

Assignment Help Electrical Engineering
Reference no: EM13282494

A) Design an integrator with an input resistanceof 1MΩ. Select the capacitor such that whenvi= +10V, vo travels from 0 to 10V in .1seconds.
B) If vi = 0 and offset voltage equals 5 mV,what is the current through R? How long will it take forvo to drift from 0 V to saturation? (Vsat =10V) Explain how to fix this drift problem?

Reference no: EM13282494

Questions Cloud

At what vds will the device go into saturation : An NMOS operating in triode region with Vds=0.1V conducts 60μA forVgs=2V. The device conducts 160μA for Vgs=4V. Calculate Vt. IfKn'=25μA/V2 , what is the device W/L What current would flow for Vgs=3V and Vds=0.15V
How to connect full-adders and half-adders to form delay : A full-adder is more generally known as a (3,2) counter, in that itadds three bits, producing a two bit result (sum and carry). A (4,3) counter sumsfour-bits, producing a three-bit result, and a (10,4) counter sums ten-bits, producing afour-bit res..
What is the option value : The annual risk-free rate is 6.0%, based on daily compounding. A1-year call option on the stock, with an exercise price of $22, is available. Based on the binomial model, what is the option's value.
What could be the maximum payment to the preferred : Kuhns Corp. has 200,000 shares of preferred stock outstanding that is cumulative. The dividend is $3.00 per share and has not been paid for 3 years. If Kuhns earned $1 million this year, what could be the maximum payment to the preferred stockhold..
Design an integrator with an input resistance of 1m? : A) Design an integrator with an input resistanceof 1MΩ. Select the capacitor such that whenvi= +10V, vo travels from 0 to 10V in .1seconds. B) If vi = 0 and offset voltage equals 5 mV,what is the current through R
How to calculate the thermochemical equations : Consider the following thermochemical equations : 8Mg(s) + Mg(NO3)2(s) ? Mg3N2(s) + 6MgO(s) ?H°rxn = -3884 kJ Mg3N2(s) ? 3Mg(s) + N2(g) ?H°rxn = +463 kJ 2MgO(s) ? 2Mg(s) + O2(g) ?H°rxn = +1203 kJ Use the above equations to calculate the ?H°f (in k..
What is the speculative premium : The Burma Hat Company's warrant is trading for $10.20. The warrant carries the option to purchase two shares of common stock for $48. What is the speculative premium if the stock price is $51.30?
Calculate the worse possible cmrr of an op amp : An op amp differential amplifier is built using four identical resistors, each havign a tolerance of ±5%. Calculate the worse possible CMRR.
You are require to summarize an article that focuses on : You are require to summarize an article that focuses on a single social issues or problem regarding a social institution in the US or at the global level. do not select an article from newspaper or abstracts, or review written by others author. The l..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What would va need to be if wanted the motor to operate

With a 500hp shunt wound DC motor, at 1800rpm, 500Vdc, FLA is 800Adc, Ra is 0.025 and Rf is 400. What would Va need to be if you wanted the motor to operate at 1000rpm at rated torque. Keeping the field current constant.

  Use technology mapping to convert the primitive circuit

Use technology mapping to convert the primitive circuit using only NOR and NOT gates. The NOT gates must be single input, the NOR gates may be any number of inputs. Show the interim circuit diagrams(s) and circle the redundant NOT gates, then show..

  Derive the magnitude and phase angle of z

Given A series RLC linear circuit with an inductor1 of 0.5 Henry, followed by a capacitor 0f 0.01 Farad, followed by another inductor2 of 0.5 Henry and a resistance of 10 Ohms. 1 Specify the input impedance of this circuit Z(s).

  Create a cron file that will regularly perform

Create a cron file that will regularly perform the following backups:?

  Explain what is the maximum message bandwith

What is the maximum message bandwith for which the system operates satisfactorily? Determine the output signal to quantizing noise ratio when a full-load sinusoidal modulating wave of frequency 1 MHz is applied to the input.

  Calculate the scalar components of the vector pointing

Two points are given P1 (1,0,1) and P2 (6,-3,0)  Calculate: a) The scalar components of the vector pointing from P1 to P2. b)The scalar components of the vector pointing from the origin to P1. c) The magnitude of the vector pointing from P1 to P2 ..

  Calculate minimum power required to operate the heat pump

Under steady operating conditions, cold water at 15 oC and 200 kPa enters the water heater with a flow rate of 54 kg/min and leaves the water heater at 80 oC and 200 kPa. During its operation the water heater loses heat to its surroundings at the ..

  Design a moore machine that has one input x and one output

Design a Moore machine that has one input X and one output Z. Provide a complete design using D Flip flops. In this design, the output should be 1 any time the sequence 01101 occurs. Overlapping sequences are allowed.

  Determine the component values of the circuit

A series RLC circuit is connected to a 5 V supply, the frequency of the supply is adjusted to give a maximum current of 11.9 mA at 2.5 kHz. The Q factor is 70. Determine the component values of the circuit.

  Discuss the choice of slope angles if the location is at 75

Determine the panel orientation you would choose to obtain maximum energy: (a) Over the year (b) In the summer (c) In the winter Discuss your choice of slope angles if the location is at 75°N.

  Determine transfer function of second-order lowpass filter

Determine the transfer function of the second-order (2 poles) lowpass Butterworth filter with a 3 -dB cutoff frequency of 5 kHz. Design it using the Sallen-key Lowpass filter configuration, find all the values of the circuit element

  Estimate the worst-case varation in film thickness

A wafer 100mm in diameter is mounted in an electron-beam evaporation system in which the spherical radius is 40cm. Use Eq. 6.7 to estimate the worst-case varation in film thickness between the center and edges

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd