Design an embedded system to turn on an led

Assignment Help Electrical Engineering
Reference no: EM13270436

Design an embedded system to turn on an LED when it is dark and turn off of LED during the day time.

Reference no: EM13270436

Questions Cloud

Obtain the rotational losses of a universal motor : obtain the rotational losses of a universal motor if you are only given the impedance, RPM, voltage,poles, frequency, current and pf Basically I need to solve for the shaft torque and efficiency but can't get my Pout value without the rotational l..
Explain bound energy of a carbon-carbon single bond found : X rays have wavelength on the order of 1*10^-10m. calculate the energy of 1.0*10^-10m X-rays in units of kilojoules per mole of X rays.AM radio waves have wavelength on the order of 1*10^4m. calculate the energy of 1.0*10^4m radio waves in units o..
Find the length of the beam at the initial temperature : The length of a beam increases by 1.26mm when its temperature is raised from 29.87oC to 71.49 oC. What is the length of the beam at the initial temperature
How fast was the drunk going just before the collision : A drunk driver in a 1700 kg car plows into a 1300 kg parked car with its brake set. how fast was the drunk going just before the collision
Design an embedded system to turn on an led : Design an embedded system to turn on an LED when it is dark and turn off of LED during the day time.
What is the profitability index for the project : If the initial outlay for such a production is $1,500,000 and the appropriate discount rate is 6 percent for the cash flows, then what is the profitability index for the project?
Find the total complex power delivered to the load : Fundamentals of Electric Circuits fourth edition: alexander, sadiku chapter 12 problem 12.29 A balanced three phase wye-delta system has Van= 120 angle 0 Vrms and Zdelta= 51+ j45 ohms. if the line impedance per phase is 0.4 + j1.2 ohms,
Compute the original speed of the bullet : A 690 g wood block is at rest on a frictionless table, when a 27 g bullet is fired into it. what was the original speed of the bullet
Find the firm dividend payout ratio and retention ratio : Drekker, Inc., has revenues of $312,766, costs of $220,222, interest payment of $31,477, and a tax rate of 34 percent. It paid dividends of $34,125 to shareholders. Find the firm's dividend payout ratio and retention ratio.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design the logic for address decoder-glue logic and dtack

A Motorola 68000 microprocessor-based data acquisition system incorporates memory ( EPROMS and SRAMS), an Analog-to-Digital Converter (A/D), a Centronics Parallel Printer, and a very simple I/I Device made up of a single push-button switch.

  Design a multi-function unit with four functions chosen

Design a multi-function unit with 4 functions chosen using select inputs s1s0. The unit has two 2-bit inputs (A = a1,a0 and B = b1,b0) and 4-bit output (z3,z2,z1,z0). The unit performs A+B (s1s0 = 00), AB (s1s0 = 01), A2+B (s1s0 = 10)

  Determine the effective data rate in bps

Two DTEs are communicating via modems and RS-232C interfaces over a half duplex link. Data transmission is one directional with each message of length M. After a message is transmitted, the sender waits for a CTS message.

  Determine the total load impedance per phase

A three-phase, 60Hz, wye-connected synchronous generator has balanced line-to-line voltages of 480V at its terminals. The generator is supplying power to two balanced and delta connected, three-phase loads. the first load is made up

  Design a double sideband amplitude modulation modulator

Design a Double Sideband Amplitude Modulation (DSBAM) modulator and demodulator system using the SystemView software. The modulating wave m(t) = Amcos(2pifmt) and the carrier wave c(t) = Accos(2?fct) have the following parameters

  Make an appropriate substitution

Use the fact that x = 2 and y = 0 at t = 0 to determine the appropriate value of the arbitrary constant in the solution set.

  Calculate the cycling periods and plot the level vs time

A 10m diameter cylindrical tank is emptied by a constant outflow of 1 m3 /min. A two position controller is used to open and close a fill valve with an open flow of 3 m3 /min. For level control the neutral zone is 1m and the setpoint is 10m.

  What is difference between logical nd arithmetic shift right

Data Transfer/Manipulation Instructions a) If accA holds $16 and accB holds $2A, what memory locations will change value after executing the STD $637F instruction. Identify the new value in any changed memory locations.

  Find interconnection between roms address and data lines

Reduce the two functions given below and implement them using fewest 8x2 ROM's. Draw a neat labeled diagram showing interconnection between the ROM's address and data lines, and content of each ROM.

  Locate and specify an appropriate sensor

Locate and specify an appropriate sensor if it is to operate at 120 vac as an input to a PLC. Create the ladder diagram program to accomplish the specified control.

  Determine the induced internal voltage and torque angle

The input power to the geenrator is 100hp. When the generator is operating at rated values and unity power factor, the generator is 80% efficient. a.) Find the generator speed in rpm and rad/sec. b.) Find the mechanical torque supplied to the gener..

  How much pressure in atmosphere must submersible be designed

Assuming that the maximum depth of Kraken Mare is less than 400 meters, how much pressure in atmospheres must the submersible be designed to withstand Assumer the surface pressure on Titan is 17 kilopascals, the surface temperature is 94 kelvin

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd