Design an active controller to achieve a settling time

Assignment Help Mechanical Engineering
Reference no: EM131149798

A damped single-degree-of-freedom system has a mass (m) of 5 kg, stiffness (k) of 20 N/m, and a damping constant of 5 N-s/m. Design an active controller to achieve a settling time less than 15 s for the closed loop system.

Reference no: EM131149798

Questions Cloud

Explain how an optimal monetary policy could influence : Explain how an optimal monetary policy could influence the global financial crisis. Support your paper with 4-5 scholarly resources. In addition to these specified resources, other appropriate scholarly resources may be included.
Process involves trading thoughts or messages verbally : When preparing an e-mail, or any form of written communication, which of the following rules is most important to obey? This process involves trading thoughts or messages verbally, in writing, or nonverbally. When you have a face-to-face conversation..
How differentiate your program from competitors programs : Consider the customer satisfaction model show below. Explain, why is it important to measure customer expectations as well as actual satisfaction from consumption or usage?
What is probability that at least one member is not tenured : The Computer Systems Department has eight faculty, six of whom are tenured. Dr. Vonder, the chair, wants to establish a committee of three department faculty members to review the curriculum. What is the probability that at least one member is not ..
Design an active controller to achieve a settling time : Design an active controller to achieve a settling time less than 15 s for the closed loop system.
What steps the company can take to improve upon its image : The action plan must outline 4 major image issues with its stakeholders and what steps the company can take to improve upon its image. Apply corporate social responsibility and environmental ethics in your paper.
Identify the dependent variable and the independent : Identify the dependent variable and the independent or explanatory variable in this study. Also, state the Null and Alternative hypotheses.
Why an international code of business ethics : Please read the Marianne Jennings article: “Why An International Code of Business Ethics Would be Good for Business” posted in DocSharing. How would the recommendations from the article make it easier or more difficult for your chosen company to cond..
Design a suitable tuned damped vibration absorber : design a suitable tuned damped vibration absorber. Determine the improvement achieved in the amplitude of the bridge with the absorber.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the wall thickness of the propane tank in mm

The welded handle and stand on the tank weigh 1 lbs (combined) and valve on the tank weighs 1.5 lbs and has an exit area of 1 cm^2 . What is the wall thickness of the propane tank in mm? what is the inner volume of the propane tank in mL and gallons..

  Find the ideal thermal efficiency of the engine on the

the volume in the clearance space of a 6 by 10 inches otto gas engine is 0.06 cubic ft. find the ideal thermal

  What is the volume of the water at the end of the process

A piston-cylinder device containing .1 Kg of saturated liquid water, initially at 1 bar, is heated at constant pressure until the temperature is 140C. an electrical heater within the device is turned on and is allowed to pass a current for 5 min from..

  A steel shaft 120 mm in diameter is supported in flexible

a steel shaft 120 mm in diameter is supported in flexible bearings at its ends. two pulleys each 500 mm in diameter are

  Energy when completely combusted in air

As a 75 slug car travels along a horizontal, 3200 ft section of road, it changes speed from 5 mph to 60 mph. During this acceleration, the car gets an average MPG of 15 MPG. How efficient is the car’s engine during the acceleration assuming 1 gallon ..

  Estimate the nominal size of the smallest sae grade 1

estimate the nominal size of the smallest sae grade 1 standard unc bolt that will not yield under a tightening torque

  Exposure of the plate to irradiation

The curing process of Example 1.9 involves exposure of the plate to irradiation from an infrared lamp and attendant cooling by convection and radiation exchange with the surroundings. Alternatively, in lieu of the lamp, heating may be achieved by ..

  The upper block just begins to slip when the amplitude is

the two blocks in the figureoscillate on a frictionless surface with a period of 1.7 s. the upper block just begins to

  Your boss asks you to calculate the flow through a

your boss asks you to calculate the flow through a natural-gas pipeline. since it is 26 in. in diameter it is

  What is the velocity of the fluid in the small section

Fluid is flowing in the pipe has two areas. The velocity of the fluid flowing in the larger area is 4 ft/s. The radius of the larger area is 4 inches. The radius of the smaller section is 2 inches. What is the velocity of the fluid in the small secti..

  The stiffness of the pumpu2019s shaft is 80 knm calculate

you balanced a pump impeller by placing a 5 gram weight at a radius of 100 mm. the original vibration amplitude was 10

  The r-134a is then heated to a final temperature of 30

r-134a is contained in a vertical cylinder fitted with a frictionless piston and a set of stops and the volume is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd