Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Design an 8-bit ripple-carry adder and draw its schematic. Useblock symbols for two circuits, a half adder and a full adder.Label all inputs, outputs, and connections. Use a half adder forthe LSB, and full adders for the remaining 7 bits. Add an activehigh overflow indicator and the required detection circuitry. Thecircuit should have inputs a7 through a0, inputs b7 through b0, sumoutputs s7 through s0, and output overflow. For all inputs/outputsuse index 7 as the MSB and index 0 as the LSB.
What will cause latch-up in a CMOS IC. What might happen in this condition. What precaution should be taken to prevent latch-up.
The high-voltage side of a transformer has 750 turns, and the low voltage side has 50 turns. When the high side is connected to rated voltage of 120 V, 60 Hz, a rated load of 40 A is connected to the low side.
a)Design the corresponding scrambler. b)Design the corresponding descrambler. c)Determine the output sequence T. d)Verify that if this T is applied to the input of the descrambler, the output is the sequence S.
1. Find cross-correlation sequence for x and y. 2. Find autocorrelation sequence for x and y. 3. Find the convolution sequence z(n) for x and y. 4. Plot above three sequences using MATLAB and verify your hand calculations for those sequences
A ones count circuit has 3 inputs A,B,C and 2-bit output YZ. YZ is 00 if none of the inputs are 1; YZ is 01 if 1 of the inputs is 1; YZ is 10 if 2 of the inputs are 1; YZ is 11 if 3 of the inputs are 1. Design a 6-input circuit that outputs a true
Adding dopants to a sample of silicon is found to reduce the Hall coefficient by a factor of 10 and increase the conductivity by a factor of 5. What effect has this dopant addition had on the mean free path
For x(t) --> Linear System --> y(t), x(t) = u(t)-u(t-1) and h(t) = 2e^-t*u(t) Sketch x(t) and h(t) Write down the generic form of the convolution integral Calculate y(t) for t 1, using the convolution integral method.
a zener diode exhibits a constant voltage of 5.6 volts for currents greater than five times the knee current.Izk is specified to be 1 ma. the zener is to be used in the design of a shunt regulator fed from a 15 volts supply .
Calculate the number of resistors and switches needed for a resistor ladder DAC for each case: a. 3 bit DACb. 7 bit DAC c. 25 bit DAC d. 42 bit DAC
The steering wheel has backlash. This means there is a delay between the time the wheel is turned, and the time the car responds. The driver tends to overturn, which leads to instability and lack of control of the car.
Compute the unit-pulse response h[n] for the discrete-time system y[n+2]2y[n+1]+y[n]=x[n] (for n = 0, 1, 2, 3).
Point A is at an electrostatic potential of +1V relative to point B in a vacumm. An electron initially at rest at B moves to A. What energy (in J and eV) does the electron have at A What is its velocity
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd