Reference no: EM131070390
• Op-Amp Circuits
Design a summing amplifier with three channels, using a 741C Op-Amp. The voltage gain of the should be 1.3, 2, and 4.7 for channel 1 to channel 3. Show the results for vout for all possible combinations of the channels in a table. Use screen shots to show vout meter readings.
INTRODUCTION
State the theory behind the lab.
Perform the calculations for the design.
EQUIPMENT
List of devices and meters used to conduct the experiment
PROCEDURE
Steps you took to carry out the lab.
RESULTS
What did you discover/confirm?
Screen shots of the meter readings.
Use tables and diagrams to record results.
Compare calculations with the measured values.
CONCLUSION
What did you learn?
LAB REPORT:
Introduction:
Write one to two paragraphs about the Lab. Explain the following information for this lab:
- What are the goals to achieve in the lab?
- What are the expectations of the lab?
- How will you be implementing this lab?
- What will you try to measure?
Equipment/Components:
Listthe type of equipment or components that you will be using? Where will you find these components? How will you use these components in Multisim/VHDL? Explain any adjustments required such as tolerances.
Procedure:
Briefly describe how you will approach the problem and try to solve the lab, describe and explain any techniques/rules/laws/principles you would use. Outline each step of the process.
Circuit design:
Take a screenshot of the circuit/logic from Multisim/VHDL as asked in the lab assignment before you run the circuit and paste it here in your report.
Execution/Results:
Run the circuit in Multisim/VHDL and copy/paste the results from the simulationincluding any readings, plots or graphs.
Copy/Paste the screenshots for all the measurements required in the lab here. Be sure to add a title and explain what each of the screenshots represent.
Analysis:
Analyze the results obtained from Multisim/VHDL and compare those to your calculated results (if required).
Answer the following questions:
- What did you discover/confirm?
- Use tables and diagrams to record results.
- Compare calculations with the measured values.
- Analyze your results.
Explain if your simulation is correct or incorrect and why. If the results are confirmed, then your measurements are correct. If they are not confirmed, explain what the problem is. You will need to discuss how to troubleshoot the circuit to achieve the correct results.
Conclusion:
Summarize the entire lab in 1 to 2 paragraphs with the results and analysis in mind.
Answer any questions asked in the lab assignment here.
Cite any sources that you may use in your report.
|
The u.s.system of volume measurement
: In the U.S.system of volume measurement, a pint is 2 cups, a cup is 8 ounces, an ounce is 2 tablespoons, and a tablespoon is 3 teaspoon. Write a program that requests a volume in cups and that displays the equivalent volumes in pints,ounces,tables..
|
|
Display the motion of the particle as an animation
: The particle is under the influence of gravity. This example was used as an example of a case where spherical or cylindrical coordinates might make the problem easier to solve than Cartesian coordinates. This extra credit assignment will examine t..
|
|
Develope a software that tests softwares
: To develope a software that tests softwares using genetic algorithm. The techniques that should be applied in the software are: selection, crossover, mutation, fitness function and termination.
|
|
Tunnel cost comparisons
: Search the internet for the link to the Boston tunnel, "the Big Dig" or the "Channel Tunnel," and London's Millennium Dome. In spite of their poor cost performance, why do you think these projects were supported to their conclusion? What would it ..
|
|
Design a summing amplifier with three channels
: Design a summing amplifier with three channels, using a 741C Op-Amp. The voltage gain of the should be 1.3, 2, and 4.7 for channel 1 to channel 3. Show the results for vout for all possible combinations of the channels in a table. Use screen shots..
|
|
Components in multisim-vhdl
: Listthe type of equipment or components that you will be using? Where will you find these components? How will you use these components in Multisim/VHDL? Explain any adjustments required such as tolerances.
|
|
Clarity of methods and assumptions
: Application of relevant course concepts, tools and frameworks use of evidences, engagement with the literature.
|
|
Find the clients living in kansas city
: Find the clients living in Kansas City. Include the client's Client No., Clast name, Cfirst name, Caddress, the name(s) of their pet(s), and their respective Quoted Prices. Save the query as CLIENTS in KANSAS CITY.
|
|
Impact of branding in sales or organisational development
: RESEARCH IN BUSINESS ASSIGNMENT - Impact of Branding in Sales or Organisational development. Impact of Branding on the business. The Revenue patterns of the company with a branding
|