Design a power electronic system

Assignment Help Electrical Engineering
Reference no: EM131067526

It is desired to design a power electronic system, referred to as ‘the device' in below, which has the following specifications:

- The device is supplied from a single-phase wall outlet which has a 240 V rms, 50 Hz specification (through terminals I1, I2).

- The device can generate a fixed ±5 V dc (through terminals O1, O2, O3).

- The device can also produce a variable 0 to 20 V dc (through terminals O4, O5).

- The device can also produce two fixed 60 V 50 Hz ac outputs, that can even be connected in series to produce a fixed 120 V ac (through terminals O6, O7, O8).

- The device can also produce a variable 0-60 V, 50 Hz or 60 Hz ac output (through terminals O9, O10). There will be a up/down button on the device to select either 50 or 60 Hz.

- The device will only have one of its outputs functioning at a time (i.e., it will not be loaded through multiple outputs simultaneously).

- The device should be able to supply a load (a variable resistor with a minimum resistance of 10 ohms), when connected to either of its output terminals.

Your Task:

1- Design the circuit and select the appropriate components for that circuit to fulfill the requirements of the device.

2- Verify your design by MATLAB simulations. (Note that different sections of the design can be simulated separately to make the simulation faster.)

Reference no: EM131067526

Questions Cloud

Accounting department at major software manufacturer : The head of the accounting department at a major software manufacturer has asked you to put together a pro forma statement of the company's value under several possible growth scenarios and the assumption that the company’s many divisions will remain..
Projectile hits the ground : A spring gun shoots a projectile with a speed V0at an angle as measured from the horizontal direction. The ground is sloped upward at an angle. Give the cooridnates (x,y) of where the projectile hits the ground.
What is the IRR for each of these projects : Garage, Inc., has identified the following two mutually exclusive projects: Year Cash Flow (A) Cash Flow (B) 0 –$ 28,900 –$ 28,900 1 14,300 4,250 2 12,200 9,750 3 9,150 15,100 4 5,050 16,700 a-1 What is the IRR for each of these projects? At what dis..
Period of oscillation of the individual masses : What is the period of oscillation of the individual masses? What is the maximum potential energy stored in the spring?
Design a power electronic system : It is desired to design a power electronic system, Design the circuit and select the appropriate components for that circuit to fulfill the requirements of the device
Calculate the relative error of the answer obtained : calculate the relative error of the answer obtained
Organization information and the costs of producing : The value of information is the difference between the benefits realised from using that information and the costs of producing it. Would you, or any organisation, ever produce information if its expected costs exceeded its benefits? If so, provid..
Acceleration of gravity on the moon : Determine the time for the feather to fall to the surface of the moon if i t dropped on the moon from a height of 1.40 meters. The acceleration of gravity on the moon is 1.67 m/s2.
Finding the required rate of return on equity capital : Finding the required rate of return on equity capital. How do I find the RE with only using information found online? I need to find it for PepsiCo and I am not sure and the book that I am studying does an awful job of explaining. Could someone expla..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What would be measured variable of air conditionning system

Draw a schematic for a home or office central air conditionning system.Label the elements. What would be the measured variable. The manipulated variable. A reasonable value for the set point. Name devices that might serve as elements.

  What range of input voltages would produce

An 8-bit ADC with a 10.0-V reference has an input of 3.797 V. Find the digital out- put word. What range of input voltages would produce this same output? Suppose the output of the ADC is 101101112. What is the input voltage?

  What is total worst case error if statistical addition used

Using data from the data sheets of the MAX505 DAC, and the various temperature coefficient of DAC errors specified at 25 degrees Centigrade, calculate the total Worst Case Error for a temperature deviation of 45 degrees Centigrade.

  Determine ratio of open-circuit voltage to built-in barrier

Solar Cell Consider a GaAs PN junction solar cell with the following parameters. Na=10^17 cm^-3, Nd= 2*10^16 cm^-3, Dn=190 cm^2/s, Dp=10 cm^2/s, Tn0=10^-7s, and Tp0=10^-8s.

  Find the mid-band gain am

Find the mid-band gain AM and the 3-dB (high) frequency of a MOS cascade amplifier as shown in the following circuit.

  If a computer executes instructions to sum the contents

if a computer executes instructions to sum the contents of memory cells 2 and 999 and store the result in cell 0what

  How many states are in the count sequence of an n-bit switch

A switch-tail counter uses the compliment of the serial output of a right-shift register as its serial input. (a) Starting from an initial state of 000, list the sequence of states after each shift until the register returns to 000.

  Explain resistance of headlights

Resistance of Headlights, A 24-volt automotive battery is connected to two headlights, such that the two loads are in parallel

  What are roles of integral term and derivative term

For PID control, what are roles of integral term and derivative term. Given KP=10, KI=3, and KD=4, write down this PID controller function.

  Explain what is the advantage of a synchronous counter

Flip-flops must be in what mode (Set, Reset, Hold, or Toggle) in order to divide a clock's frequency when building a counter What is the advantage of a synchronous counter as compared to a ripple counter

  Porter five competitive forces

Porter's Five Competitive Forces

  Design and simulate a power supply that takes line voltage

Design and simulate a power supply that takes line voltage and produces a 15V output with less than .5% ripple voltage. For your design, provide all the data sheets, calculations and simulations for the output characteristic

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd