Design a minimum-weight hollow circular steel column

Assignment Help Mechanical Engineering
Reference no: EM131146103

Design a minimum-weight, hollow circular steel column for the water tank shown in Fig. 3.72. The weight of the tank (W) is 100,000 lb and the height is 50 ft. The stress induced in the column should not exceed the yield strength of the material, which is 30,000 psi, when subjected to a harmonic ground acceleration (due to an earthquake) of amplitude 0.5 g and frequency 15 Hz. In addition, the natural frequency of the water tank should be greater than 15 Hz. Assume a damping ratio of 0.15 for the column.

2349_6261f8d3-0803-4fcb-a959-4cbe6ce94000.png

Reference no: EM131146103

Questions Cloud

Why is it important to have evidence for cam therapies : Identify three examples from the professional literature or the Internet that illustrate how EBP is used in health promotion and disease prevention using CAM therapies.
Finding the total response of a spring-mass-viscous-damper : Write a computer program for finding the total response of a spring-mass-viscous-damper system subjected to base excitation. Use this program to find the solution of a problem with
What is the topic of the reaseach : Based on the article what is the topic of the reaseach?-  Based on the article what are the finding from your reasearch?
Explain the effectiveness of your program evaluation : Explain how your group conducted its formative evaluation, including the measures you took to ensure that your process would be successful and how you addressed any challenges that arose. Then, explain how this formative evaluation helped your gro..
Design a minimum-weight hollow circular steel column : In addition, the natural frequency of the water tank should be greater than 15 Hz. Assume a damping ratio of 0.15 for the column.
The health insurance portability and accountability act : The Health Insurance Portability and Accountability Act of 1996 (enacted in 200) established guidelines for how providers and facilities should protect protected health information.
Explain how the experience connected your classroom studies : Explain how the experience connected your classroom studies to the real-world clinical setting. If you did not have an opportunity to evaluate a patient with this background during the last 9 weeks, you may select a related case study from a reput..
Decision essay - profit planning and control : Managerial Decision Essay - Profit Planning and Control, In early 2015, RadioShack, an electronics retailer,began closing sales at over 1,700 stores as part of its major restructuring after declaring bankruptcy
What was your plan for diagnostics and primary diagnosis : What details did the patient or parent provide regarding the personal and medical history? Include any discrepancies between the details provided by the child and details provided by the parent, as well as possible reasons for these discrepancies.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the preassure at the bottom of the gate

A square 3m x 3m gate is located in the 45* sloping side of a dam. Some measurements indicate that the resultant force of the water on the gate is 500kN.(a)Determine the preassure at the bottom of the gate.(b)Show on a sketch where this force acts..

  For the diffuser shown in the attached image find the mass

a diffuser is a device that the flow of air in order to recover a pressure loss. for the diffuser shown in the attached

  Determine the corresponding specific stagnation enthalpy in

steam flows through a passageway and at a particular location the pressure is 3 bar the temperature is 281.48c and the

  Determine the temperature drop during this process

Refrigerant-134a is throttled from saturated liquid state at 7 bar to a pressure of 1.4 bar. Determine the temperature drop during this process and the final specific volume.

  Determine the deflection for this shaft at the center

A torque T is introduced from the right end of the shaft and removed at the gear wheel. The number of stepped section is given, however the length of each section and their diameters are unknown and need to be determined. Determine the length and ..

  At what time does the hour hand point in the same direction

a clock face has negative point charges -q -2q -3q middot middot middot -12q fixed at the positions of the

  Determine the maximum compression in each of spring bumpers

The train engine on the left, A, is at rest, and the one on the right, B, is coasting to the left. If the engines are identical, use numerical values to show how to determine the maximum compression in each of the spring bumpers that are mounted in t..

  Calculate the temperatures at the compressor and turbine

air enters the compressor of a simple gas turbine non-ideal brayton cycle at p1 14 lbfin.2 t1 520 degree r. the

  Why do you think it is important to control the position

why do you think it is important to control the position of a dc motor? provide two examples for position control of

  Demand for a particular product is normally distributed

demand for a particular product is normally distributed with a mean of 100 units and a standard deviation of 20 per

  Time required for balls to attained a temperature of 150

Calculate the time required for the balls to attained a temperature - suddenly placed in a control environment in which the temperature is maintained at 100oC.

  The specific humidity on leaving is decreased to one-third

an air-water-vapor mixture enters a cooler-dehumidifier at the rate of 1000 ft3min. the mixture enters at 14.7 psia

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd