Design a low-pass unity-gain butter worth filter

Assignment Help Electrical Engineering
Reference no: EM13293809

Using 3kohm resistors and ideal op amps, design a low-passunity-gain butterworth filter that has a cutoff frequency of 20 khz and is down at least 25 dB at 100 khz.

Reference no: EM13293809

Questions Cloud

Show a block diagram for the implementation : For the same functions,we have available as many of the decoders described below as needed plus 2 eight-input OR gates.Show a block diagram for this implementation. All inputs areavailable both uncomplemented and complemented.
Find the direction of the magnetic force on the rod : Parallel conducting tracks, separated by 2.79 cm, run north and south. There is a uniform magnetic field of 1.27 T pointing upward (out of the page). What is the direction of the magnetic force on the rod
What was the original u.s. dollar value of the zim dollar : On August 1, 2006, Zambabwe changed the value of the Zim dollar from Z$101/U.S.$ to Z$250/U.S.$
What is the magnetic flux through the desk surface : A horizontal desk surface measures 2.52 m x 2.05 m. If Earth's magnetic field has magnitude 0.463 mT, what is the magnetic flux through the desk surface
Design a low-pass unity-gain butter worth filter : Using 3kohm resistors and ideal op amps, design a low-passunity-gain butterworth filter that has a cutoff frequency of 20 khz and is down at least 25 dB at 100 khz.
Explain the amount of product that can be lost as a result : If you used 20 ml water to recrystallize salicylic acid at 10 °C, estimate the amount of product that can be lost as a result of dissolving in the filtrate. (solubility at 10 °C =0.14/100 ml water). Calculate the loss if you had used 4 mls of wate..
Which of the below are considered cash management techniques : Which of the below are considered cash management techniques?
Supply of diamonds : Suppose there is a simultaneous increase in the demand for diamonds and increase in the supply of diamonds. Which of the following will occur as a result of these simultaneous events?
Find the net force on the given charge : A -10uC charge is 3cm away from a +10uC charge. and is 4cm to the left from a +64uC charge. Find the net force on the +10uC charge

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the number of binary digits required to encode

A compact disc (CD) records audio signals digitally by usingPCM. Assume that the audio signal bandwidth equals15kHz. a) If theNyquist samples are uniformly quantized into L = 65536 levels andthen binary-coded

  How many simultaneous users may be supported for less ber

In a DSSS multiple user system, how many simultaneous users may be supported such that an average BER of less than 10E-3 is maintained for each user if the average Eb/No=10dB, and a Pg from a straight code of 11 bit shift register length or the Np..

  Give a brief explanation of the concept of priority encoder

Give a brief explanation of the concept of a priority encoder. Using this, what would be the binary output for a 10-input priority encoder when inputs 7 and 5 are activated What is the binary output (active-high) Active-low

  Determine the value of current through the capacitor

determine the current through the capacitor, i_c(t) for time t greater than or equal to zero if the following  statements apply. 1. Vc(t=0) = 5V 2. The switch is closed from t = - infinity to t = 0.2 seconds, when it opens.

  Determine what is the sensor output rms voltage amplitude

The unloaded output of a sensor is a sinusoid at 200 Hz and 5V rms amplitude. Its output impedance is 2000+600j. If a 0.22 μf capacitor is placed across the output as a load, what is the sensor output rms voltage amplitude

  Find cutoff frequencies if sampling frequency in 30 khz

Sketch magnitude and phase responses (as linear gain versus digital frequencies) for each filter (use [0,π]). Indicate filter type. Find cutoff frequencies if sampling frequency in 30 kHz. Use 6 points only. Do not use MATLAB.

  Find what value of cannel width must the design use

For a particular IC-fabrication process, the transconductance parameter kn'=400 micro amps/v^2 and vt=0.4V. In an application in which Vga=Vds=Vsupply=1.8, a drain current of 2mA is required of a device of minimum length of 0.18um.

  Find the motors running speed and the power output

A permanent magnet motor is driving a load that requires 0.08Nm.The motor data is:RA =2W, VA =12v,Kt =0:05Nm/A ,KG = 0:004 V/RPM . Find themotors running speed and the power output.

  Sketch the unit step response of the system

Sketch the unit step response of the system below. Show the magnitude of the steady state on the c(t) axis of your response curve and the value of the time constant on the t axis. T(s)=C(s)/R(s)=5/s+2.5

  Determine the wave number and the angular frequency

the wavelenght of green light Lamda =550nm. Determine the wave number, the angular frequency,and the peroid of the wave. The speed of light is 3*10^8 m\s.

  Explain why then do even use jfets as amplifiers

Why then do we even use JFETs as amplifiers. What is it that make them attractive even though they are non-linear. How do we minimize the effect of their non-linearity

  Calculate the traffic load per cell

The system uses a 7-cell reuse pattern. If the offered traffic per user is 0.03 Erlangs and the average number of calls per hour per user is 1.5, for an Erlang-C system with a probability of delaying a call being 5%, calculate the traffic load per..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd