Design a logic circuit that takes the output of buttons

Assignment Help Electrical Engineering
Reference no: EM13291456

At a design review for your first engineering project, you presentthe project to a panel of three senior engineers who will vote onwhether your project should be funded or not. The senior engineerswill vote using an electrical switch with two positions. A vote of yes will be provide five volts at theoutput of the switch. A vote of no will provide ground, or zerovolts at the output. (See figure). If at least two of the engineersvote yes, the project will be funded.
This will be indicated by a green LED being lit. Otherwise, the LED will not light and the project will not be funded. Design a logiccircuit that takes the output of the buttons and lights the LED if a majority votes yes.

Reference no: EM13291456

Questions Cloud

Find the rotor current when the machines is running normally : a 3-phase slip ring induction motor gives a reading of 60volts,across a slip ring of open circuit. When at rest with normal statervoltage applied, the rotor is star connected and has an impedanceof (0.6+6j)Ω per phase.
Find the motors running speed and the power output : A permanent magnet motor is driving a load that requires 0.08Nm.The motor data is:RA =2W, VA =12v,Kt =0:05Nm/A ,KG = 0:004 V/RPM . Find themotors running speed and the power output.
How does this affect one role as a counselor : Addiction distorts the image of God in human beings and adversely impacts sanctification in a believer. He also mentioned that some believers can struggle with addictions. Discuss why you agree or disagree with his statements
Determine the counter torque and the power input : A permanent magnet generator has Kt = 0:02Nm/A . The terminal voltage is six volts. It is spinning at 2500 rpm. It is connected to a load with a resistance of 30W. Determine the counter torque and the power input.
Design a logic circuit that takes the output of buttons : At a design review for your first engineering project, you presentthe project to a panel of three senior engineers who will vote onwhether your project should be funded or not. The senior engineerswill vote using an electrical switch with two posi..
Explain cyclohexane-toluene mixture : Distillate (condensate) in four separate containers,~1mL in each, during the fractional distillation of 4mL of a (1:1) cyclohexane-toluene mixture, and then obtain IR spectra for each fraction
What is the use of the carry output in parallel load counter : What is the use of the carry output in a parallel load counter If l have a 3 bit binary parallel load counter do l connectthe count input,and the outputs (Q) from the three flip flops
Explain what is the mass of a cylinder of mercury : Mercury has the density of 13.6 g/cm3. what is the mass of a cylinder of mercury with a tube with an inside diameter of .45 cm and a height of 76.0 cm
Introduction on the roles played by managers in organisation : Select three short articles from magazines or newspaper which depict three different roles played by managers in organisations. identify and analyse each of the managerial roles as described in the articles.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the impulse response for the system

noncausal, linear, and time-invariant. Determine the impulse response for the system and verify that an LTI system defined by the impulse response you determined satisfies the difference equation.

  Determine the operating state if vd is given

An enhancement-type NMOS transistor with Vt=2 V has its source grounded and a 3-V DC source connected to the gate. Determine the operating state if a. vd = 0.5 V b. vd = 1 V c. vd = 5 V

  What sampling rate should use for aliasing frequencies

use a third-order low pass filter with a -3dB frequency of 10 Hz to filter your signal. What sampling rate should you use to make sure any potentially aliasing frequencies are attenuated by at least -40 dB for a. A butterworth filter

  Determine what is the forward parasitic resistance

A diode is measured to pass 0.31mA at 0.70V forward bias, and 1.12mA at 0.75 V forward bias. What are its n and Is. Assume that kT/q=0.026V. For extra credit, if the diode passes 4mA at 0.9V forward bias, what is its forward parasitic resistance

  Calculate the per unit resistance of this transformer

Efficiency in a power transformer is 98.6 percent when loaded such that its copper losses are five times its core losses. Calculate the per unit resistance of this transformer.

  Find what donor concentration is needed to current density

In a 10-μm long bar of donor-doped silicon, what donor concentration is needed to realize a current density of 1 mA/μm2 in response to an appliedvoltage of 1V.

  What is the electric field for r- inside the sphere

A sphere has a radius d and contains a non-uniform charge density of Pv=Po(1-r/d) C/m^3. (a). What is the enclosed Charge for r d (c). What is the electric field for r

  What is the maximum distance the trace can be from the ic

A sensitive IC (integrated circuit) on a circuit board is located 1m from a long power line carrying 10A. The power line generates a magnetic field. You can place a trace on a circuit board with current running parallel to the power line to cancel..

  Compute direct beam insolation normal to the suns rays

A south-facing collector at latitude 40%u25E6 is tipped up at an angle equal to its latitude. Compute the following insolations for January 1st at solar noon: a. The direct beam insolation normal to the sun's rays.

  Calculate the hole diffusion current density versus x

The total current in a semiconductor is constant and is composed of electron drift current and hole diffusion current. The electron concentration is constant and is equal to 10^17 cm^-3. The hole concentration is given by p(x)

  Explain why the instant applied voltage is interrupted

An electronic timer consists of a resistor whose value is 10,000 ohms, a capacitor of 30 pico farads, and a 10 volt source which is applied across the RC connection at time t =0.

  Determine the counter emf of a shunt motor armature

a certain shunt motor armature has a resistance of 0.07 and a current of 50 amperes at 120 volts. determine the counter emf

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd