Design a flow control station just downstream

Assignment Help Mechanical Engineering
Reference no: EM131719336

Overview

A pump and piping network transfers water from an in-ground sump to a storage pond located on a nearby hill (Figure 1). Please design a flow control station just downstream of the pump. In particular, specify the details of orifice plate FO-100 and flow control valve FCV-100.

1236_figure.jpg

Figure 1

Design the orifice and flow control valve by following these steps.

1) Establish the orifice diameter at the target flow rate.

2) Input your diameter in the FO block.

3) Compute and plot the system curve, including the pressure drop across the orifice but without the control valve, over a range of flows slightly broader than the control range.

4) Compute the pump curve

5) Design the control valve using the heuristics presented in class. Give the results of your design by filling in the blocks highlighted in yellow on the IEC 60534-7 control valve spec sheet.

6) Enter your values for valve open percentage, valve pressure drop, and valve mass flow rate at the design flow rate

How does your manually calculated value of Cv at 100% open compare to the value given by HYSYS?

7) Using the HYSYS-generated value of Cv, compute the system curve with the control valve using the same procedure as you employed in step 3). Co-plot this system curve with the previous system curve and the pump curve. Confirm that the system curve with the control valve intersects the pump curve at the design flow rate.

Attachment:- Flow Control Station on a Water Pipeline.pdf

Reference no: EM131719336

Questions Cloud

Wrote the song tumbling tumbleweeds : Nolan wrote the song "Tumbling Tumbleweeds" and, in an agreement with Sam Fox Publishing Company, transferred all rights to the song to the company.
Compute the location where a central distribution warehouse : compute the location where a central distribution warehouse should be located to minimize transportation, based on center of gravity.
Who was obligated to notify blackston of the assignment : The clerk of the court assigned the right to receive the payments to the Department of Human Resources.
Discuss the term personal jurisdiction : What does it mean when the court must have "personal jurisdiction" and describe the primary manner in which it differs from long arm jurisdiction
Design a flow control station just downstream : Flow Control Station on a Water Pipeline - CHE 4353-Process Control - Design the control valve using the heuristics presented in class.
Key operations and supply chain management questions : How does vaccine distribution relate to key operations and supply chain management questions including: quality management, new product development.
Firm save annually in ordering and carrying costs : How much could the firm save annually in ordering and carrying costs by using the EOQ?
Find the value of the mean point difference : Find the value of the mean point difference and the value of the median point difference for the 11 games.
Transform a conceptual model into a logical model : Analyze why user, security groups, and role definitions are essential to maintain the integrity of the database.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine stresses acting on the faces of an element rotated

Determine the magnitude and direction of the principal stresses on the surface of the shaft.- Determine the stresses acting on the faces of an element rotated 20° clockwise.

  Determine the back work ratio and the thermal efficiency of

consider a gas-turbine cycle with two stages of compression and two stages of expansion. the pressure ratio across each

  Compute the number of kilograms of hydrogen

Assume a diffusion coefficient of 1 × 10-8 m2/s, that the concentrations at the high- and low-pressure sides of the plate are 2.4 and 0.6 kg of hydrogen per cubic meter of palladium, and that steady-state conditions have been attained.

  What is its density specific weight and specific gravity

An object is constructed of a material lighter than water. It weighs 50 N in air and a force of 10 N is required to hold it under water. What is its density, specific weight, and specific gravity?

  Water filled manometer is attached to the inlet

A water filled manometer is attached to the inlet and the test section of a low speed wind tunnel which has the contraction ratio of 3. what would be the pressure difference between the inlet and the test section in terms of inches of water in order ..

  Determine the maximum load which can be applied

Determine the number of cycles for a defect to grow from 1.5mm to 4 mm - determine the maximum load which can be applied if brittle fracture is not to occur. Use a factor of safety of 3.

  Quality of the refrigerant and the pressure at final state

A well-insulated piston-cylinder device initially contains 5kg of saturated mixture of refrigerant-134a at -12°C, in which 2.55kg of the refrigerant is in the liquid phase. An electric switch is turned on, and a 110-V source supplies current to a res..

  A gas is contained in a vertical fractionless- cylinder

a gas is contained in a vertical fractionless- cylinder device. the piston has a mass of 4 kg and cross sectional area

  Governing equations of motion for a two degree

The purpose of this project is to derive the governing equations of motion for a two degree of freedom (planar) gantry-type robot that is commonly called an H-Bot (Fig. 1).

  Find the pipe diameter

If the galvanized iron pipe connecting the two locations is 200 ft long and contains six threaded 90° elbows, determine the pipe diameter. Elevation differences are negligible.

  Determine the minimum distance d at which the brakes must

a vehicle a is stuck on the railroad tracks as a train b approaches with a speed of 120 kmh. as soon as the problem is

  Determine the following 1 the compressor work kjkg 2 the

an ideal cold air-standard brayton cycle engine operates with air entering the compressor at 27 c. the pressure ratio

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd