Design a double-stub tuner using open-circuited stubs

Assignment Help Electrical Engineering
Reference no: EM131105393

Repeat Problem 5.9 using a double-stub tuner with short-circuited stubs and a 3λ/8 spacing.

Problem 5.9 Design a double-stub tuner using open-circuited stubs with a λ/8 spacing to match a load admittance YL = (0.4 + j1.2)Y0

Reference no: EM131105393

Questions Cloud

How the net income for the sixth is affected : If yes, assume that net income for the fifth year and the sixth year is the same andexplain how the net income for the sixth is affected (compared to that for the fifth year)?
Find two designs using open-circuited stubs : Find two designs using open-circuited stubs.
Which of the following would you expect to happen : Investors expect a company to announce a 10% increase in earnings; instead, the company announces a 1% increase. If the market is semi-strong form efficient, which of the following would you expect to happen?a. The stock's price will increase slightl..
Question regarding the times-interest-earned ratio : If the company could reduce its accounts receivable to the point where its DSO was equal to the industry average without affecting its sales or its operating costs, how would this affect (a) its free cash flow? (b) its return on common equity? (c)..
Design a double-stub tuner using open-circuited stubs : Problem 5.9 Design a double-stub tuner using open-circuited stubs with a λ/8 spacing to match a load admittance YL = (0.4 + j1.2)Y0
Make a change in its overhaul operation : An airline maintenance base wants to make a change in its overhaul operation. The present situation is that only one airplane can be repaired at a time, and the expected repair time is 36 hours, whereas the expected time between arrivals is 45 hou..
How much depreciation and amortization expense : How much Depreciation and Amortization Expense did Target record in Fiscal 2009? How much was the Depreciation Expense alone (i.e. excluding Amortization)?
Formulation of financial strategies for businesses : What is the importance of ethics in the formulation of financial strategies for businesses?
What is the maximum value of normalized reactance : What is the maximum value of normalized reactance that can be obtained with a shorted stub of the same type of transmission line? Assume α is small.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What units and physical significance of area under pulse

At t = t0, the voltage across a certain capacitance C is zero. A pulse of current flows through the capacitance between t0 and t0 +?t, and the voltage across the capacitance increases to V f . What can you say about the peak amplitude Im and area..

  What is device conversion efficiency at maximum power point

Isc of 3.3A under input power Pinput=1kW/m^2. Assuming diffusion dominated behavior and no parasitic resistance elements, what is the device conversion efficiency at the maximum power point

  How many bits are the virtual and physical page numbers

Consider a virtual memory system that can address a total of 232 bytes. You have unlimited hard drive space, but are limited to only 8 MB of semiconductor (physical) memory. Assume that virtual and physical pages are each 4 KB in size.

  How many units must we sell to recover increased design cost

a cost to produce, P, of $4.00. If we were able to reduce this to $3.55 through greater attention in the design, and if the cost to improve the design (in NRE) is $35,000, how many units must we sell to recover the increased design cost.

  Find the voltages vab-vbc and vca at the load

the rms voltage of a balanced 3 phase Y connected source is 110 volts at 60Hz. it is connected to a balanced Y Load by 3 distribution lines with an impedence on each line z=1+j2. the load impedence is z=19=j28 per phase.

  Performing the next bptt computation, where h''

Specifically, we may let the network go through h' additional steps before performing the next BPTT computation, where h'

  Design each of the circuits specified in procedure section

Design each of the circuits specified in the Procedure section of this lab. Your design should attempt to get within § 5 % of the specified gain. All designs are to use standardcommercial 5 % resistors. You may only use a single resistor for each ..

  Determine the power factor of the combined load as seen

Three capacitors are found that each have an impedance of -j2.0, and they are connected in parallel with the load in a wye configuration. Determine the power factor of the combined load as seen by the source.

  If loop consists of loop what is the radius along the loop

A current of 4 A flows through a wire forming a "loop" circle of radius r. If the magnetic field in the center of the "loop" is 10 A, what is the radius along the "loop": a) if the loop consists of a loop of wire, b) if the "loop" consists of 20 t..

  Find the conditional probability that they come within edges

a laser weapon is fired many times at a circular target that is 1m in diameter and it is found that one-tenth of the shots miss the target entirely. for those shots that miss the target completely

  Overlap with frequency components from the ekg

You notice low frequency noise (which is near but does not overlap with frequency components from the EKG) due to respiration in your final set-up.  Describe how you could generate a filter that would remove this noisy frequency component after data ..

  Determine for copper at 20 degree c the resistance

The resistivity of copper is 1.724 micro-ohm-cm at200C. Determine for copper at 200C the resistance (a) of a cylindrical conductor 1 meter long and having a diameter of 1mm; (b) a rod 2 meters long and having a diameter of 2mm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd