Design a digital scale using a force transducer

Assignment Help Mechanical Engineering
Reference no: EM131090023

Design a digital scale using a force transducer. Select the range of the scale to match the linear range of your force transducer. You can build a force transducer using a slide pot and a spring. Design your system with the best possible resolution. The force measurements will be displayed as fixed-point numbers on an LCD. Experimentally verify the noise level, time-constant, and accuracy of your system

Reference no: EM131090023

Questions Cloud

Capital raising in project evaluation : What if these assumptions cannot be met? How do we treat issue costs relating to capital raising in project evaluation?
Design a thermocouple-based thermometer : The temperature measurements will be displayed as fixed-point numbers on an LCD. The temperature component is 0 to 1 Hz. Experimentally verify noise level, time-constant, and accuracy of your system.
Computing the cost of external equity : MMM Manufacturing will issue common stock to the public for $40. The expected dividend and the growth in dividends are $3.6 per share and 5%, respectively. If the flotation cost is 10% of the issue's gross proceeds, that is the cost of external eq..
Hype regarding social media and its impact : 1. Mindful note-taking can prevent unintentional plagiarism.
Design a digital scale using a force transducer : Experimentally verify the noise level, time-constant, and accuracy of your system
Wwe cost of equity : WWE's current EPS is $5. It was $3.736 five years ago. The company pays out 40% of its earnings as dividends, and the stock sells for $36. What is WWE's cost of equity, rs?
Design two digital position measurement systems : Experimentally verify the noise level, time-constant, and accuracy of both systems.
Limited partnership investment : Three years later, she was required to contribute $2,000 more to the partnership. Two years ago, she was required to contribute an additional $2,000. If Cameron sells her limited partnership investment today for $20,000, what are the taxes?
Design an autoranging voltmeter : Experimentally determine the measurement resolution for each range and compare it to the expected theoretical resolution. Analyze the various sources of measurement error in your system.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Time constant related system-diffusion related system

Explain the fundamental difference in scaling principles between a “time constant related system” and a “diffusion related system”. Briefly describe an example of how the similarity approach for the analysis of scaling can break down when applied to ..

  P8mpa and t500 degc and leaves at 40 kpa as saturated vapor

p8mpa and t500 degc and leaves at 40 kpa as saturated vapor. if the flow rate is 11.1 kgs and the power generated by

  Part 1 - energy in the home personal energy use and home

part 1 - energy in the home personal energy use and home energy efficiency.estimate your personal annual energy usage

  If a current of 80.0 ma exists in a metal wire,

If a current of 80.0 mA exists in a metal wire, how many electrons flow past a given cross section of the wire in 10.0 min?

  The cube that sits above interface between the two liquids

A cube 2 ft on an edge has its lower half of material with SG = 1.4 and upper half SG = 0.6. It is fully submerged in a 2 layer liquid (lighter liquid above has SG = 0.9 and heavier liquid below has SG = 1.2). Determine the height of the top of the c..

  A sample of silty clay has a volume of 1488cm3 a total

a sample of silty clay has a volume of 14.88cm3 a total mass of 28.81 g a dry mass of 24.83 g and a specific gravity of

  Determine if a simple supported w12 x 26 a36 steel beam

determine if a simple supported w12 x 26 a36 steel beam has the capacity to support loads that produce 50ksi of

  Determine the final pressure using a approximate analysis

air is compressed isentropically from an initial state of 300 k and 101 kpa to a final temperature of 1000 k. determine

  Heat is transferred to a cylinder having a fixed volume of

heat is transferred to a cylinder having a fixed volume of 6 m3 containing 0.1 m3 of saturated liquid water and 5.9 m3

  Calculate the thrust produced by the motor on a test

at rated thrust a liquid-fueled rocket motor consumes 180 lbms of nitric acid as oxidizer and 70 lbms of aniline as

  Compute the critical resolved shear stress

Consider a single crystal of nickel oriented such that a tensile stress is applied along a [001] direction. If slip occurs on a (111) plane and in a [101] direction, and is initiated at an applied tensile stress of 13.9 MPa (2020 psi), compute the..

  One kmol of ideal gas cp30 jmolk is contained in a piston

one kmol of ideal gas cp30 jmolk is contained in a piston cylinder initially at 25c and 10bar. the mass of the piston

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd