Design a concrete column of 14 ft high to support a dead

Assignment Help Civil Engineering
Reference no: EM13546922

1.Discuss the characteristics of waste that are favorable for biological treatment, thermal processing, recycling, and landfilling.

2.A 1.5 meter deep vertical wall trench is to be cut in a soil whose unit weight is 17.36 kN/cubic meters, angle of internal friction is 25 degrees, and cohesion is 20.6 kN/square meters. Determine the factor of safety of this trench by the Culmann Method.

3.Design a concrete column of 14 ft high to support a dead load of 80 kips and a live load of 200 kips? f'c= 6,000 psi fy= 60,000 psi

Reference no: EM13546922

Questions Cloud

What is the final temperature of the water : A piston-cylinder device contains 2 kg saturated water vapor at 600 kPa. The water expands adiabatically until the final pressure is 100kPa. And 1,465 kJ work is produced.
Does the second law require that the decrease in entropy : An insulated system contains two solid blocks in contact with each other; one hot and the other cold. After heat transfer over some time,thermal equilibrium is established in the container.
What is the rate of entropygeneration assuming the surround : Steam expands in an turbine operating in steady-state conditions with a mass flow rate of 40,000 kg/hr. The steam enters the turbine at 8MPa and 500 C, and exits as a saturated vapor at 40 kPa. If the power generated by the turbine is 8.2 MW, what is..
What is the rate of cooling for the refrigerator : Some skin divers go as deep as 50m. What is the gage pressure at this depth in fresh water, and what is the ratio of the absolute pressure at this depth to normal atmospheric pressure? assume T=20 degrees celcius
Design a concrete column of 14 ft high to support a dead : Design a concrete column of 14 ft high to support a dead load of 80 kips and a live load of 200 kips? f'c= 6,000 psi fy= 60,000 psi
Calculate the required downpayment and monthly payments : Terry wants to purchase a used car for $8000. The dealer offered to finance the deal at 8.5% APR for 4 years with 10% down payment. Terry's bank will provide a loan at 7.8% for 3 years,
Requires you to compile an annotated bibliography : This assignment requires you to compile an Annotated Bibliography
Calculate the monthly loan payment to repay : It is not uncommon to borrow $100,000 or more to purchase a home. Banks typically offer 15-,20-, and 30- year loans. a) Calculate the monthly loan payment to repay a $100,000 home loan
Create a depreciation schedule showing annual depreciation : Create a depreciation schedule showing annual depreciation amounts and end-of-year book values for a $26,000 asset with a 5 year service life, using the MACRS depreciation method.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the forecast of the theoretical relational test

You have batched both of the mixes you designed in questions 6 and 7 on the same day and have made a sufficient number of 6" diameter and 4" diameter cylinders of each mix so that two cylinders of each size

  Compute the true static height

A Kennedy half dollar has a mass of 1.150 X 10-2 Kg. The coins is a mixture of silver and cooper, and in water weights 0.1011 N. What is the mass of the silver?

  Find the principal moments of inertia and the principal axes

find the inertia tensor about the origin for a mass of uniform density=1,inside the part of the unit sphere where x>0,y>0,and find the principal moments of inertia and the principal axes.

  Find the maximum deflection of a wooden bearer

Find the maximum deflection of a wooden bearer which has three supports; one at each edge (2) and one in the middle (2m from each other). Bearer holds a UDL over its whole length (4m) of 600 N/m.

  Find the pressure at the forward and rear corners along the

A closed box with horizontal base 6m x 6m and height of 2m is half-filled with water and is accelerated Ax=4.9 m/sec^2 and Ay=-2.4 m/sec. find the pressure at the forward and rear corners along the bottom.

  What are the basic assumptions of the traffic flow model

What are the basic assumptions of the 'traffic flow model' and 'capacity model' used in signal timing design. Discuss.

  Determine the speed of the collar when it has moved

Springs AB and CD have a stiffness of k = 300 N/m and k' = 200 N/m, respectively, and both springs have an unstretched length of 600 mm. If the 2-kg smooth collar starts from rest when the springs are unstretched

  Find cable forces f-q and p is directed along the z-axis

The vertical post is secured by three cables. The cables are pre-tensioned so that the resultant of the cable forces F, Q, and P is directed along the z-axis. If F =120lb, find P and Q.

  Find what is the angle that is formed by the crane boom

A crane is placed along the easterly sideline of a building, but 25 feet from the front of the building. The building to be erected is a 6 story building that is 100 feet wide by 50feet deep. YOu may assume that each story is 15 feet.

  Estimate the hourly so2 and particle emissions

what type of SO2 removal device before (in front of) or after (following) the particle collector would you use?

  Find the torsional moment t for the maxiumum shear stress

The pipe has an outside diameter of 60mm and an inside diameter of 50mm. Find the torsional moment T if the maxiumum shear stress is 80MPa.

  Determine the value of the dynamic viscosity at conditions

Start from the values for the density and the kinematic viscosity of CO2 at 15o C and standard atmospheric pressure (101.3 kPa), and first determine the value of the dynamic viscosity at the same conditions.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd