Design a combinational circuit that has four inputs

Assignment Help Electrical Engineering
Reference no: EM13286617

design a combinational circuit that has four inputs (ABCD) and one output(Z). The output equals one when the Gray coded number represented by ABCD is less than five. Reduce the function using SOP or POS forms and then partially factor if possible. Utilize a decoder to realize this function.

Reference no: EM13286617

Questions Cloud

What is the output resistece r0 for each of the two case : An IC NMOS transistor has W=100μm, L = 10μm,μnCox= 20μA/V2, VA= 100 V, γ = 1/2 V1/2, Vt0= 1V, and 2φf= 0.6V. calculate the value of Vt at VSB= 4V. Also for VGS=3V and VDS=5V, Calculate ID for VSD = 0V and for VSB = 4V
State and write a net ionic equation : A. Write a net ionic equation . B- for the reaction in part a, write the equilibrium constant from a consideration of Kb and Kw. C- calculate the h3o^+ for a 0.45 M nh4cl solution . D- calculate the percent of hydrolysis of 0.45 M NH4Cl.
Write vhdl module for the parallel-in and parallel-out shift : write a VHDL module for the parallel-in, parallel-out right-shift register of figure 12-10 (page 360), but add an active-low asynchronous clear signal ClrN. Do not use individual flip-flops in your code. simulate the module to obtain a timing diag..
Explain a column elution with non polar solvents : why does one begin a column elution with non polar solvents and progress to more and more polar solvents
Design a combinational circuit that has four inputs : design a combinational circuit that has four inputs (ABCD) and one output(Z). The output equals one when the Gray coded number represented by ABCD is less than five. Reduce the function using SOP or POS forms and then partially factor if possible.
Explain ea in the absence of conversions : In temperature dependance of reaction rates, if you use R=8.314 J/molxK, what should the units be for Ea in the absence of conversions
Compute the vertical components of the launch velocity : In a football game a kicker attempts a field goal. The ball remains in contact with the kicker's foot for 0.0398 s, compute the  vertical components of the launch velocity
How man output bits will the decoder produce : To play music, these types of players have a decoder circuit that can decode the binary representation of the piece of music to be played. The electronic signals corresponding to the notes that are to be 'played' can then be transmitted to a speak..
Explain which method is more efficient of extractions : When performing extractions it is often better to do multiple extractions rather than one large volume extraction. suppose you have 100mg of a sample dissolved in 0.6ml of water.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine if the ct signal is periodic

Determine if the following CT signal is periodic. calculate the fundamental period T0 for the CT signal: x(t) = 2cos(4*pi*t/5)*sin^2(16t/3)

  Calculate the time required for the voltage to fall to 1 v

An RC circuit with a time constant T = 30 msec has reached a steady state of 2 V at time t = 0. The circuit is then suddenly switched to ground (0 V). Calculate the time required for the voltage to fall to 1 V.

  Find the input impedance of the transmission line

A 1(lambda) wavelength long line has parameter R=0.2 Ohm/m, G=0.002 mho/m, L=15 muH/m and C=2.31pF/m. The line is operated at a frequency f=2.5 GHz. It is terminated with a load impedance of 100 Ohms.

  Find the voltage across the 20-ohm resistor initially

A coil of 10H inductance and 5Ω resistance is connected in parallel with a 20Ω resistor across a 100-V DC supply which is suddenly disconnected. Find The voltage across the 20Ω resistor initially and after 0.3 sec.

  What is maximum voltage if current is required to be bigger

A 50-cm-long copper wire with a cross-sectional area 1.2286x10^-10 m^2 is used to connect a voltage source and a device. What is the maximum voltage if the current is required to be not bigger than 5A

  Calculate min number of pn bits required for each frequecy

Calculate the minimum number of PN bits required for each frequency hop for an FHSS system that employs a total bandwidth of 800 MHz and an individual channel bandwidth of 200 Hz. If this system uses MFSK modulation in conjunction with FHSS

  Determine the value of impulse function h at t

Consider an ideal op-amp in inverting amplifier configuration with feedback impedance Rf=6ohms and an input impedance consisting of a series RL: Ri=6ohms and Li=5H. Let h(t) be the impulse response of the overall amplifer.

  Design clocked synchronous state machine with state table

Design a clocked synchronous state machine with the state/output table shown below. Use D flip flops. Also use two state variables Q1 and Q2 with the state assignment AA = 00, B = 01, C = 11, and D = 10

  Design an open-circuited-shunt stub matching network

Design an open-circuited, shunt stub matching network to match a 125 + j20 ohm load to a 700 MHz, 50 ohm generator. Show the lengths of your transmission lines in fractions of a wavelength. Show steps to solution please.

  Calculate the minimum value of vd

Calculate the minimum value of Vd if the power flow through the converter is 5 kW (a) from the ac to the dc side and (b) from the dc to the ac side.

  Select a pulse whose magnitude spectrum is constant

A pulse is used to measure the frequency response of a system. Since we expect the frequency response to extend to 20 kHz, we want to select a pulse whose magnitude spectrum is constant within 1% out to 20 kHz.

  Write a logic expression for g by supposing a and b

Suppose A and B are 3-bit signed-magnitude numbers and A =(A2, A1, A0) and B = (B2, B1, B0). a) Write a logic expression for G, which is true when and only when A > B.  b) Write a logic expression for GE, which is true when and only when A ≥ B.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd