Design a circuit to multiply two 2-bit numbers

Assignment Help Electrical Engineering
Reference no: EM13291998

Design a circuit to multiply two 2-bit numbers -a,b and c,d and produce a 4-bit product -w,x,y,z. Show the truth table and the equations.

Reference no: EM13291998

Questions Cloud

Compute the average net force exerted on the ball : A billiard ball strikes and rebounds from the cushion of a pool table perpendicularly. The mass of the ball is 0.38 kg. What is the average net force (magnitude and direction) exerted on the ball by the cushion
Calculate the diode capacitances at a biases of 0v : A silicon diode with an area of 100mm´100mm is doped with ND=2e17cm-3 and NA=1e20cm-3. It has an IS=1fA, nonidealityfactor n=1 and tT=1ns. Consider room temperature of 300 Degree Kelvin.
Provide a brief statement on the issue : Should be succinct and to the point describing what the project is about. It is generally a one sentence statement and provide a brief statement on the issue and a concise outline of the paper content and structure.
Linear programming problem : Formulate the problem of finding the minimum cost way of sending flow through the network, from the source nodes to the sink nodes, subject to the node supplies/demands and the arc capacity restrictions, as a linear programming problem.
Design a circuit to multiply two 2-bit numbers : Design a circuit to multiply two 2-bit numbers -a,b and c,d and produce a 4-bit product -w,x,y,z. Show the truth table and the equations.
Determine the potential at the vertex : the right triangle with vertex P at the origin, base b, Determine the potential at the vertex P
What is the rms load current and determine the turns ratio : A step-down transformer has a 120V rms primary voltage applied and a 12V rms voltage is measured at thesecondary. Assuming the transformer can be considered ideal,determine the turns ratio, n.
What are some of the principal social institutions : What are some of the principal social institutions that are involved in music production and reception in your world? How do these various institutions contribute to the ways in which you experience, understand,and value the music that are a part of ..
Find to what voltage is the capacitor charged : The 95 mu F capacitor in a defibrillator unit supplies an average of 6500 W of power to the chest of the patient during a discharge lasting 5.0 ms

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the power dissipated by the top surface of chip

A rectangular chip has a top surface of 0.5 cm by 2 cm cooled by air at 20 oC with h = 150 W/m2.K. There are also 16 connector pins, 1 mm wide, 0.5 mm thick, 6 mm long and k = 60 W/m.K attached to a circuit board at 30 oC.

  What potential will be required to reduce photocurrent

The work function of platinum is 4.09ev what retarding potential will be required to reduce the photocurrent to zero in a photoelectric experiment with Pt electrodes if the wavelength of the incident light is 2440 angstrom

  What range of voltage would be expected to be measured 2 sec

A manufacturer specification sheet lists the transfer function of a pressure sensor as 45±5% mV/kPa with a time constant of 4±10%. A highly accurate test system applies a step change of pressure from 20 kPa to 100 kPa.

  Give subroutine to perform lower-to-upper case conversion

Write and test a program for the EASy68k to input a string from the keyboard, convert all letters to uppercase and echo (output) the new string to the screen. Use a subroutine to perform the lower-to-upper case conversion.

  Design the electronic processor that must be connected

The converter canreceive signals from 0 V to 5.0V. Design the electronic processorthat must be connected between the sensor´s output and thecomputer´s converter A/D input; so that maximum sensibility is obtained. Justify each single proposal you m..

  Determine the maximum torque occurs at starting

A three phase, 25-hp, 440-V, 60-Hz, 1750 rpm, wound-rotor induction motor has the following equivalent circuit parameters: R1=0.20 ohms, X1=1.0 ohms, R2=0.15 ohms, X2=0.8 ohms, Xm=30 ohms. The motor is connected to a three phase, 440-V, 60-Hz supply.

  Determine the average voltage of the waveform

A rectangular waveform has a 50% duty cycle (high for 1/2 acycle and low for 1/2 a cycle). It goes between two voltage levelsof -3 V (low) and +8 V (high), and has a period of100μs. a. Determine the Average voltage of this waveform.

  Calculate the maximum va rating of the autotransformer

Suppose a standard single-phase transformer that has a rating of a 15 kVA, 600V/120V, 60 Hz is reconnected as an autotransformer to obtain 600 V primary to 720 V secondary voltage ratio.

  Determine the closed loop bandwidth of a compensated opamp

A compensated op-amp has an open loop low frequency gain of 10^5 and an open loop -3db frequency of 10 Hz. If an inverting amplifier with a closed loop low frequency gain of 100 uses this op-amp, determine the closed loop bandwidth.

  What will be potential difference between plates seperation

An Air capacitor consisting of two closely spaced parallel plates has a capacitance of 1000 pF. The charge on each plate is 1 micro C. What is the potential difference between the plates. If the charge is kept constant.

  Determine the rom size and contents to implement a function

Determine the ROM size and contents to implement a function which converts a sign and magnitude number from -5 to +6 to two's complement format.

  Describe a linear circuit which contains a voltage source

Suppose a linear circuit contains a voltage source and a current source. When the voltage source is set to 10V and the current source is set to 10 mA, the output voltage is 1V. When the voltage source is set to 10V and the current source is set to..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd