Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
There are four oscilloscopes , A ,B, C,D in a laboratory that areequipped with individual indicator circuits. There indicator circuits give our a logic 1 any time the scope mal functions. Design a circuit that would be able to indicate that three or more of the scopes malfunctioning.
a voltage v(t) = 24cos(2000t-45degrees) is applied across a parallel connection of a 5kΩ resistor and 100nF capacitor. find the steady state current ic(t) through the capacitor and ir(t) through the resistor.
a 20 mH inductor with an internal resistance of 20 ohms is connected in series with a capacitor and a voltage source with a thevenin resistance of 60 ohms. a. what value of C will be needed to produce Wo = 6 krad/s
Suppose q1 = 10. nC is located at the Cartesian coordinate point (4.0 m, 0.0 m, 0.0 m). A second charge q2 (-4.0 m, 0.0 m, 0.0 m) = -10. nC. If a test charge qt(0.0 m, 0.0 m, 3.0 m) = 0.10 nC
Two three-phase loads are y-connected across a 300 Volt three phase line. One load draws 10kW at a p.f. of 0.9 leading, and the second load draws 8kW at a p.f. of 0.6 lagging. V(line-neutral)=300V/sqrt(3)=173.21V
Design an analog computer circuit to solve the following differential equation 1)Draw the state flow diagram 2)Design and draw the OpAmp circuit. Show the values for the resistors and capacitors. Label all inputs and outputs
A three-phase wye-delta transformer is rated 225-kV:24-kV, 400 MVA and has a single-phase equivalent series reactance of 6.08 ohms as referred to its high-voltage terminals. The transformer is supplying a load of 375 MVA
A point charge Q is located at (0,0,d) above an infiniteconducting plane that lies in the xy-plane and is maintained atground potential. Find a) the surface charge density as a functionof x and y on the conducting plane
A cable technician tested the signal-to-noise ratio on the curb as 20 dBm. This means, if the noise power is at 1 mW, then the signal power should be 20 dB higher then that. If the noise power is 20 mW
Calculate and plot the required current and the resulting voltage Va that should be applied to the armature terminals of the machine. As intermediate steps, calculate and plot Ea, the required electromagnetic torque Tem from the motor, and the cur..
The range of an analog signal is 2 Vpp, and the samples of this signal are being quantized. The quantizer-output word size is 10 bit. What is the quantization interval Q
For a 12-bit linear PCM code with a resolution of 0.02 V, determine the voltage range that would be converted to the following PCM codes. (a) 1 0 0 0 0 0 0 0 0 0 0 1 (b) 0 0 0 0 0 0 0 0 0 0 0 0 (c) 1 1 0 ..
In the question below only focus on the parameter or parameters that are relevant to the particular property you are being asked about in the particular question. If you need to constrain a parameter to satisfy the stated criterion.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd