Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Oven Controller
Assume that an oven has an electronic thermometer attached to circuitry with two outputs: one (H) is asserted when the temperature is above h, and the other (L) is asserted when the temperature is below l. Design a circuit that will turn the oven on when the temperature falls below l; turn the oven off when the temperature rises above h; and when the temperature is between l and h, leave the oven in the condition it was in before l or h was reached. Design this controller as a state machine.
Write the HDL code and simulate the design. In your report, provide the HDL code, and show the simulation waveforms of your working design. In addition, show the RTL schematic resulted from the tool and report any interesting parameters such as highest clock frequency of the design.
Two charges are held fixed in an x-y plane. Charge Q=-1*10^-9 C is located at the origin, q=3*10^-9 C is located at (0,2). Determine the voltage (v_ba) between point 'b' located at (3,0) and point 'a' located at (1,0).
Let x[n] = [1,2,3,2,1] with arrow under 3 and y[n] = [2,1,0,-1,-2] with arrow under 0. a) using scanning operation, determine and plot correlation sequence between two signals. b) Determine and plot correlation coefficient.
Let y[n] = Odd{x[n+1]}, where Odd{f[n]} takes the odd part of f[n]. Determine if this system is a. Linear b. Time invariant c. Causal For each part, either show proof that the property holds or show an example that it does not.
Determine the Laplace transform of the above signals (use properties of the Laplace transform) including the corresponding region of convergence.
The magnitude of the acceleration of the block is 1.93 m/s^2 (a) Find the coefficient of kinetic friction between block and plane? I got 0.393 but it is wrong. (b) Find the speed of the block after it has slid 1.90 m
A cyclotron used to accelerate alpha [articles (m=6.55 x 10^-27kg, q=3.2x10^19C) has a radius pf .50, and a magnetic field of 1.8T (a)what is the period of revolution of the alpha particles (b)what is their kinetic energy
Consider a regenerative Rankine cycle with a 600C and 4-MPa throttle, a 5-kPa condenser, and an open feedwater heater at 500 kPa. Turbine efficiencies are 85%. (a) Draw labeled, coordinated T-s and flow diagrams.
A state government is considering construction of a flood control dike having a life span of 15 years. History indicates that a flood occurs every 5 years, on average, and causes $600,000 in damages on each occasion.
Using DC Operating point analysis in Multisim (DO NOT USE MULTIMETER INSTRUMENT-NO CREDIT) determine the emitter voltage and emitter current. Provide a screenshot of the results window.
a.) What isthe minimum sampling frequency to avoid aliasing b.)If the sampling frequency of fs=2500 samples/sec is used how many samples must be taken to give a frequency resolution of 10Hz
(a) Design a high-pass filter with a cutoff frequency of 40 kHz. Use 0.01 uF capacitor and an appropriate resistor. B) Sketch and label the circuit. C) What is the gain of the filter at the cutoff frequency Give your answer both as ratio (Vout/Vin..
What is the bandwidth occupied by this signal, and the noise bandwidth of the receiver for this signal? Find the BER at the receiver output and the average time between errors.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd