Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
design a 4-bit serial adder (VHDL code or schematic) which includes two shift registers and a single full-adder to perform the following functionality with proper timing controls. Two 4-bit inputs A and B will be set by eight switches on your Xilinx board. Inputs S will control two modes of operation, when S=0 your circuit will perform a serial addition of A and B,A+B,and when S=1 output will be subtraction of B from A,A-B When the 4-bit inputs A and B, and S switch is ready, pressing a pushbutton R will start operation and without further inputs the result will be ready and stable on one of the 7-segment displays. Changing the inputs A,B and S will not change the result on the 7-segment display until the pushbutton R is pressed again.
Make a sketch of the band diagram for an n-type semiconductor and a p-type semiconductor doped with phosphorus and boron at 5*10^15/cm^3 respectively. Label all the features of your drawing, as well as the relative energy
A buck converter has Vs=30 V, Vo=20 V, and a switching frequency of 40 kHz. The output power is 25 W. Determine the size of the inductor such that the minimum inductor current is 25 percent of the average inductor current.
Explain the operation of sequential logic devices and evaluate the output waveform in relation to the clock for QA, QB and QC in the subsequent circuit and show the binary sequence represented by these waveforms
Two input capture events occur at counts 0xBA47 (first event) and 0x42B3 (second event) of the free-running counter. How many counts have transpired between these two events
An unknown semiconductor has Eg = 1.1 eV and Nc = Nv. It is doped with 10^15 cm^-3 donors where the donor level is 0.2 eV below Ec. Given that Ef is 0.25 eV below Ec, calculate ni and the concentration of electrons and holes in the semiconductor ..
consider two groups are students, where the first group has 7 women and 3 men and the second group has 5 women and 5 men. Agroup is selected randomly and then students in the selected group are randomly arranged. Suppose the probability of choosin..
Design a synchronous sequential circuit with one input line and one output line that recognizes the input string x = 1111. The circuit is also required to recognize overlapping sequence such that if the input string is x = 1101111111010
Three loads are connected in parallel across a single-phase source voltage of 240 V (RMS). Load 1 absorbs 12 kW and 6.667 kVAR; Load 2 absorbs 4 kVA at 0.96PF leading; Load 3 absorbs 15 kW at unity power factor.
Design a signal conditioning circuit for a K-type thermocouple, which produces output voltage of 0V-5V using a three terminal solid-state temperature sensor for reference junction compensation. The sensitivity of the sensor is 4mV/C.
A jet engine is modeled as a serial combination of a compressor, an adiabatic constant pressure combustor, and a turbine. Air (considered to have a variable specific heat) is compressed through a compression pressure ratio of 8.25:1
What is the common-mode rejection ratio (in dB) if the output voltage is measured to be 2.0 Vp-p when the input terminals are connected together and a 0.1 Vp-p voltage is applied between the inputs and ground.
how to determine the sensitivity of junction depth to changes in furnace temperature by calculating (dxj/xj)/(dT/T) for a drive diffusion.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd