Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
design an 8-bit programmable microprocessor-compatible TIMER IC by doing the following steps: Specify, draw , and clearly label( the functional name), the complete set of 8-bit registers that will be needed in the TIMER. All registers should be 8 bits. Specify and draw the other digital hardware building blocks needed inside the TIMER to enable it perform timing functions. Identify the one register whose bits will be specified to indicate what timing applications the TIMER will be capable of performing, based on how it has been programmed at any given moment. Specify what role each of the 8 bits of such a register will represent. List three timing applications that the TIMER can be programmed to perform. For each application, specify the binary values of all the bits in that register described in item ‘c' above.
You are designing a PCS base station that operates at 1800 MHz. The receiver is co-located on a tower with UHF police and business radio systems that operate at 450 MHz. Since the the 4th harmonic from the UHF system is directly in the PCS band
A long hallway has three doors, one at each end and one in the middle. A switch is located at each door to operate the incandescent lights along the hallway. Label the switches A, B, and C. Design a logic network to control the lights.
On a breadboards, hook up an IR LED to provide an infrared light source for signaling the phototransistor as shown in Figure 2 below. Use a pushbutton switch to turn the IR LED on and off.
Consider the Norton equivalent circuit with respect to terminals 'a' and 'b' for the circuit shown below. Suppose that Ro is given as 10 . The Norton equivalent current must be zero because there are no independent sources.
design a sequential circuit that continuously computes the function 2X + 3 or 3X + 1 where the variable X is a three-bit unsigned integer available on a serial interface. A special external data signal (DATA_READY) is asserted
An LVDT is used in an accelerometer to measure seismic-mass displacement. The LVDT and signal-conditioning output is 0.31mV/mm with +/-2cm maximum core displacement.
Working with wired rifle microphones and radio microphones, The theatre's concerns when changing of wired rifle microphones to a radio microphone system are
A 120 V separately excited DC Motor is operated at a fixed field current. It has an armature resistance Ra = 10 ohms, and a machine constant K = 0.1 V/rpm. The armature current is 0.5 amps with no load, and 3.0 amps at full load.
calculate the capacitance of the capacitor and the inductance of the inductor. for the capacitor it's going to be 1/(j*2*pi*frequency*capacitance) and (j*2*pi*frequency*inductance) for the inductor but what are the valves for the capacitance and ..
A bowling ball is placed on a coil spring. The spring constant is 400N/m. When the bowling ball is placed on the spring, the spring compresses down 0.1m. If the spring is vertical how far will the bowling ball go
Sketch the Bode plot (including the magnitude response and phase response) of a continuous- time LTI (Linear Time-Invariant) system described by the following transfer function: \(H(s) = 5(s + 2)/s^{2}(s + 10)\)
Sketch the Capacitance-Voltage characteristics for both devices based on part (d) by giving appropriate labeling to the voltage and capacitance axis. You may assume high f measurements.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd