Design 2-shell pass and 8-tube pass heat exchanger for

Assignment Help Mechanical Engineering
Reference no: EM13617842

Design 2-shell pass and 8-tube pass heat exchanger for heating ethyl alcohol from 25°C to 70°C at a rate of 2.9 kg/s. Water is available at 95°C can cool down to 45°C.

The ½ inch ANSI schedule 40 standard steel copper tubes are to be used for the construction of heat exchanger. Need to determine number of tube passes based on heat transfer area. Based on heat transfer area get suitable length and diameter of the heat exchanger (length/Diameter > 2).

Reference no: EM13617842

Questions Cloud

Two points along a straight stick of length 39 cm are : two points along a straight stick of length 39 cm are randomly selected. the stick is then broken at those two points.
For this maximum flowrate determine the values of static : standard atmospheric air at stagnation conditions t0 59 degree f p0 14.7 psia is drawn steadily through a
A sample of women were divided into four age groups group : a sample of women were divided into four age groups group a 20-45.9 group b 46.0-55.9 group c 56.0-65.9 and group d 66
Assessment matters assessment matters as a teacher you : assessment matters ltbrgt ltbrgtas a teacher you need to have solid knowledge of formative and summative assessment
Design 2-shell pass and 8-tube pass heat exchanger for : design 2-shell pass and 8-tube pass heat exchanger for heating ethyl alcohol from 25degc to 70degc at a rate of 2.9
A batch of 100 motors has been manufactured and andy and : 1. a batch of 100 motors has been manufactured and andy and bob are applying a standard stress test to them. andy is
At one instant the center of mass of a system of two : at one instant the center of mass of a system of two particles is located on the -axis at 2.0m and has a velocity of
The gas undergoes complete combustion with 120 of the : a power generator burns natural gas consisting of 30 ethane 60 methane and the balance nitrogen. the gas undergoes
Two sinusoidal waves with the same amplitude a and : two sinusoidal waves with the same amplitude a and frequency f travel in opposite directions along a long string. you

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Diffusion coeffiecient and calculate constant

Diffusion Coeffiecient, Calculate Constant, The diffusion coeffiecient for Cr^+3 in Cr2O3 is 6x10^-15 cm2/s at 727 degrees Celcius and is 1x10^-9 cm2/s at 1400 degrees Celcius.

  A common aluminum alloy al-2024 contains 44 wt copper 15

a common aluminum alloy al-2024 contains 4.4 wt. copper 1.5 wt. magnesium and 0.6 wt. manganese. the balance is

  Determine the minimum tensile strength each cable must have

due to a poorly designed foundation the statue at point a slowly slides down a grass covered slope. to prevent further

  The midpoint temperatureis 0 degrees celcius determine the

a spherical communication satellite with a diameter of 2.5m is orbiting around the earth. the outer surface of the

  What are some of the potential drawbacks

Simics Central Simics can simulate real workloads at reasonable speeds Is the reported performance a result of optimization or simulator simplicity? What are some of the potential drawbacks of making a completely general simulation environment?

  The temperature of the steam entering the turbine is 700 f

a rankine cycle operates between pressure limits of 500 and 2 psia. the temperature of the steam entering the turbine

  If the melting temperature for some alloy is 750oc at what

the melting temperatures for various materials are listed in the inside cover of callister. some representative values

  Evaluate the effect of the water spray on efficiency

Evaluate the effect of the water spray on efficiency (net work out divided by heat input) and net power out per kg/s of dry air coming into the turbine.

  Estimate the surface temperature of the pod if the air

a spherical underwater instrument pod used to make soundings and to measure conditions in the water has a diameter of

  A steel tensile specimen with starting gage length 20 in

a steel tensile specimen with starting gage length 2.0 in and cross-sectional area 0.5 in2 reaches a maximum load of

  Explain what is the amplitude of the response x

In the idealized model attached shown, m = 15 kg, k = 135 N/m, and the viscous damping ratio is 0.15. Assume that an external harmonic force F(t) = 15 cos 4 t acts on the system with F0=15 N and forcing frequency of 4 rad/s.

  Calculate the diameter of a medium carbon steel pin in

calculate the diameter of a medium carbon steel pin in double shear subjected to a suddenly applied shearing force of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd