Describes the candidates approach to solving a major issue

Assignment Help Civil Engineering
Reference no: EM131369475

You are the social policy director for a presidential candidate who will be taking part in a nationally televised debate about education policy. Your job is to write an opening statement that describes the candidate's approach to solving a major issue in education: the rising cost of college.

You should write your statement as a three- to four-paragraph essay. Remember, you have conducted research about education policy and the rising costs of higher education. Your opening statement should engage the audience, summarize your findings, and provide a clear policy approach.

Reference no: EM131369475

Questions Cloud

Characteristic of competitive markets : A characteristic of competitive markets (perfect competition), as well as monopolistic competition is the absence of entry and exit barriers. This means that new firms can easily enter the market, and it is also easy to exit the market. Firms woul..
What is probability that a randomly chosen bill is from east : If a bill is chosen at random, what is the probability that it is from the Midwest?- What is the probability that a randomly chosen bill is from the East?
Hourly pay for production line workers : Explain how each of the following will affect the average fixed cost, average variable cost, average total cost, and marginal cost curves faced by a steel manufacturer:
Analyzes future impact of social problem you have mentioned : SOCI212- Complete a 5 page final paper that analyzes the future impact of this social problem you have mentioned in the second writing assignment.
Describes the candidates approach to solving a major issue : Write an opening statement that describes the candidate's approach to solving a major issue in education: the rising cost of college.
Production takes place in a separate manufacturing facility : Leased building for management personnel, where the monthly lease payment is set based on current market rates. Actual production takes place in a separate manufacturing facility.
What are company financial objecives : What are your company's financial objectives? What are your company's strategic objectives? How would you describe your company's strategic intent?
What is current macroeconomic situation of chosen country : What is the current macroeconomic situation of your chosen country? What are two major macroeconomic problems in this country and what is the main cause of each problem
Accuracy and reliability of behavioral measurement : What procedures can be used to minimize the threats to the accuracy and reliability of behavioral measurement? Please discuss at least two procedures.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Identify the thread of a machine screw

A machine screw is found with no information given as to its size. The following data are found by using a standard micrometer caliper: The major diameter is 0.196 in; the axial length for 20 full threads is 0.630 in. Identify the thread.

  Determine the heat removed in the cooling process

Atmospheric air at 1.01 bar 30 c and 60 percent relative humidity flows over a set of cooling coils at an inlet flow rate of 1500 m^3/min the liquid which condeness is removed from the system at 17 c subsequent heating of the air results in the final..

  What was the velocity of a just before impact

Suppose you are to investigate an accident in which a 1300 kg car A struck a parked 1200 kg car B. All four of B’s wheels were locked and skid marks indicate that B slid 2 m after impact.

  Determine the maximum acceleration from rest

A rear-wheel-drive car 2600 lb, has an 80-inch wheelbase, a center of gravity 20 inches above the road surface and 30 inches behind the front axle, a drivetrain efficiency of 85%, 14-inch-radius wheels,

  Determine the average normal stress developed in each post

If all the posts have the same original lenth before they are loaded, determine the average normal stress developed in each post when post C is heated so that its temperature is increased by 20 degrees F.

  What is total delay for cycle for the saturation flow rate

A signal approach has 20 seconds of displayed green, 4 seconds of yellow, and 3 seconds of all red (assume typical start-up, lost time, and clearance time). The cycle length is 60 seconds.

  Suggest an alternative engineering design solution that

Stormwater controls are typically designed by civil engineers. Stormwater is collected in pipes below the ground and routed to nearby surface water

  Bernard is a principal in a consulting engineering firm he

bernard is a principal in a consulting engineering firm. he is also a principal owner in a construction contracting

  Determine force exerted by the hydraulic cylinder on boom

A hoist mechanism is attached to the back of a pickup truck. The crate being moved by the hoist shown below weighs 200 lbs. Note: Point A is directly above point B and the vertical distance between points A and B is 16 inches.

  Determine the reactions on the beam

Determine the reactions on the beam. The support at B can beassumed to be a roller.

  How to sketch p-v diagram as the pressure is raised

The phase diagram of a typical simple substance contains three phases , liquid vapor and solid separated by boundaries . The critical point terminates the liquid-vapor transition, in water it is at Pc=220.9 bar and Tc=374 degres celcius

  Method to reduce energy transfer

In all but a very few vehicles today crush or crumple zones are employed as a method to reduce energy transfer to the occupants in a crash.  For the most part crumple zones form a structural part of the car such as frontal rail or rear bumper beam..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd