Describe the water surface profiles at the various parts

Assignment Help Civil Engineering
Reference no: EM13555082

1.A long wide rectangular channel carries a steady flow rate of 35 m2s-1 (flow per unit width) and passes through an abrupt change in slope from 0.005 (upstream of the change) to 0.003 (downstream). Manning’s n for the channel is 0.013. Is there a hydraulic jump in the channel and if so where? Describe the water surface profiles at the various parts of the channel.

2.Water enters a very wide rectangular channel (Manning’s n = 0.0149) at a velocity of 12.2 ms-1 and a depth of 0.61 m. An H3 curve forms downstream and the water jumps to a depth of 2.4 m some distance downstream. Find the distance downstream to the location of the hydraulic jump

Reference no: EM13555082

Questions Cloud

How much heat is added to the room during a 50-minute class : Normal human skin and clothing temperature indoors is approximately 30 o C. In order to maintain this temperature, one student sitting in a classroom gives off heat at a rate of 14 watts per degree K in temperature difference between the person and t..
What is the effective interest rate : A student bought a $75 used guitar and agreed to pay for with a single $85 payment at the end of the 6 months. assuming semiannual (every 6 months) compounding, what is the normal annual interest rate? what is the effective interest rate?
What mass of petcock should be used to maintain a pressure : What mass of petcock should be used to maintain a pressure of 100 kPa gage for a cross-sectional area of 4 mm2 at the opening? Atmospheric pressure is 100 kPa.
What is the change in volume of the cylinder : A piston-cylinder device contains 0.85 kg R-134a at 263K. The piston is free to move and has a mass of 12 kg and diameter of 25 cm. The atmospheric pressure is 98 kPa. Heat is added to the cylinder until the R-134 temperature = 10 o C.
Describe the water surface profiles at the various parts : .Water enters a very wide rectangular channel (Manning’s n = 0.0149) at a velocity of 12.2 ms-1 and a depth of 0.61 m. An H3 curve forms downstream and the water jumps to a depth of 2.4 m some distance downstream. Find the distance downstream to the ..
How much subsidence would be expected from an elastic : How much subsidence would be expected from an elastic confined aquifer that has a specific storage of 2.0*10^-6 (ft^-1), a decline in pressure of 200 (lbs/in^2), and aquifer thickness of 400 ft, and a porosity of 32 percent? Assume the aquifer temper..
Determine the concentration of the pits overflow stream : A company has been discharging its waste into a holding pit for a long time. For the last several years, the pit has been full and overflowing into a local river. The waste concentration has been nearly constant at 10 mg/L of the pollutant of interes..
Calculate the critical depth and critical slope : A flow of 28 m3s-1 occurs in an earth-lined canal having a base width of 3 m, side slopes of 1(vertical) to 2 (horizontal) and the Manning’s n value of 0.022. Calculate the critical depth and critical slope
Find at what velocity does the ice skater move backwards : A 65kg ice skater standing on frictionless ice throws a .15 kg snowball horizontally at a speed of 32m/s. At what velocity does the ice skater move backwards

Reviews

Write a Review

Civil Engineering Questions & Answers

  The 50-lb block rests on the rough surface for which the

the 50-lb block rests on the rough surface for which the coefficient of kinetic friction is 0.2. a forcenbspf 40 s2

  Calculate the change in reservoir pore volume in barrels

A reservoir cover is 12,000 acres and is 20 feet thick. The formation has initial porosity of 0.25. The pore volume compressibility of the reservoir rock is 3.0 x 10^(-6) psi^(-1) .

  Determine what is the work done by the wire at ambient temp

A wire is kept at ambient temperature while it is stretched by 200 mm by a force which rises from zero to 1.5 kN, the extension of the wire being directly proportional to the force applied. What is the work done by the wire

  Find the location-velocity and acceleration of a box

The motion of a box on a spiral conveyor is defined by the following position vector: r = 0.5sin(2t) i + 0.5cos(2t) j - 0.2t k where r is in meters and t is in seconds. Find the location, velocity, and acceleration when t = 0.8 s.

  Develop preliminary wbs for small one-story to be construct

The exterior and interior walls are of concrete block. The roof is constructed of bar joists covered with a steel roof deck, rigid insulation, and built-up roofing.

  Fundamentals of hydraulic engineering

A stabilization pond is designed for a 35-day detention time. If the pond is maintained at a capacity of 40 acre-feet, what is theaverage gpd flow to the stabilizaiton pond?

  How many gpm would the fluid coming into the 1.75 flexible

If you hace 80' of flexible hose that is 1.75" ID and a pump that is a 4" and moves fluid at 100gpm, how many gpm would the fluid conimg into the 1.75" flexible hose?

  Find concentration of acetone in river due to pulse release

The water velocity is estimated to be 3.0 m/sec. Acetone has a density of 0.786 gm/mL and a half-life in water of 20.0 hr. Determine the concentration of acetone in the river due to this pulse release at distance of 2, 4, and 7 km from the site at..

  How to design for a cultivated land with sandy loam soil

The bund channel is to be formed by the embankment only. The horizontal distance between two bund s is 50 m. The 1-hr rainfall expected during the recurrence interval of 10 yrs is 8 cm/hr.

  How do you determine the cross-sectional area of the concret

How do you determine the cross-sectional area of the concrete and steel and the stresses in each if the column deforms .01 inch while carrying 100 K load? The cross sectional area is 15 inch and column height is 10 feet.

  Determine the length of the tangent of the curve

The proposed highway has two tangents of bearings N 45Degrees 54' 36" E and N 1 Degree 22' 30" W. The highway design engineer, attempting to obtain the best fit for the simple circular curve join these tangents, decides that the external is to be ..

  Calculate the pressure at the clay-sand interface for two

Calculate the pressure at the clay-sand interface for two cases:1) clay on top of the sand and 2) clay on the bottom of thevertical sand column.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd