Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
If an AM signal has an un-modulated carrier voltage Vc=A volts(pk) and a load resistance RL of B ohms. How to calculate the Pc (Carrier Power)? If the modulation index is known as m, how to calculate the Sideband Power (Psb)? Also, what is the total power Ptotal?
A synchronous motor is rated as 250 hp, 4.8 kV connected 60 Hz 12 poles with Xs=0.6 pu and Rs=0.01 pu. The motor rotational losses are 1.5 kW and the excitation power is 6 kW. The motor is supplied by rated voltage at the stator.
Capacity, Data and Transfer Rates, Access Time of Disk Drive, A hard disk drive has 10 disks and 18 surfaces available for recording. Each surface is composed of 200 concentric tracks and the disks rotate at 7200 r.p.m.
an unknown sensor is investigated by connecting resistors across the output and measuring the current through them. When a resistance of 30 is connected the current through it is 0.5A. When the resistance is replaced by 20
What is the thermal noise level of a channel with bandwidth 10kHz carrying 1000. Watts of power at 50o C?
Suppose a linear circuit contains a voltage source and a current source. When the voltage source is set to 10V and the current source is set to 10 mA, the output voltage is 1V. When the voltage source is set to 10V and the current source is set to..
The solution to Power Factor, Two single-phase loads are connected in parallel across a 415 V, 50 Hz supply. One load is rated 130 kW at a power factor of 0.75
A balanceed three-phase load of 15 MA with a lagging load factor of 0.85 is supplied by a 115KV subtransmission line. if the line impedance is 50+j100Ohm per phase, determine the following: (a) The line current of the load.
Design a circuit that, given a 2-bit value, will light a LED corresponding to that value. One of four LEDs should be lit for each of the four possible input values (binary 0 through 3).
MOSFET Amplier Sketch the 4-resistor bias network for an amplier with an n-channel enhancement-mode MOSFET, with R1 = 1Mohm ; R2 = 1:5Mohm ; RD = 75kohm ; Rs = 39kohm ; K = 25microA/V2 ; VDD = 10V and Vto = 1V.
Consider the signal x (t) = 10+ 20 cos (100*2 t + 4) + 10 cos (250*2 t ) A. Using Euler's relation, the signal x(t) defined by the above equation can be expressed as a sum of complex exponentials in the form X(t) = x0 + Re{k=1N Xkejk2fot}
A generator is rated at 500 MVA (three phase) and 22 kV (line-to-line). Its Y-connected windings have a reactance of 1.1 per unit. Find the ohmic value of the reactance of the windings. What is the per unit value if we change the base to 200 MVA a..
Construct a truth table for the following specifications: if any two consecutive switches out of four on-off switches in a row are on, then a light is on; otherwise, the light is off. Denote the switches in order as a, b, c, d,
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd