Reference no: EM133094650
Control Systems And Automation
Assessment - Modelling Of Processes And Control Devices And Systems
Question 1. A steady state distillation process is shown diagrammatically as FIGURE 1.
![869_Control Systems And Automation7.jpg](https://secure.expertsmind.com/CMSImages/869_Control Systems And Automation7.jpg)
Assuming no heat losses to the atmosphere:
(i) Write four balanced equations for this system.
(ii) Identify where any. constitutive equations may be required for the modelling processes
Question 2. A process can be represented by the first order equation
4dy(t)/dt + y(t) = 3u(t)
Assume the initial state is steady (y = 0 at t = -0).
(a) Determine the transfer function of this process in the s domain.
(b) If the input is a ramp change in u(t) = 4t, determine the value of y(t) when t = 10 s.
Question 3. Using a simulator of your own choice, or the one used during the lessons at the website;
note the initial values used by the simulator and the output produced. For BOTH ON-OFF and PID control,
(a) sketch (or print copies) of the effect of changing the following parameters from their existing value (resetting them to the original after every change has been recorded):
(i) Increasing the proportional control by a factor of 10.
(ii) Decreasing proportional control by a factor of 10.
(iii) Increasing the integral control by a factor of 10.
(iv) Decreasing integral control by a factor of 10.
(v) Increasing the derivative control by a factor of 10.
(vi) Decreasing derivative control by a factor of 10.
(vii) Increasing the hysteresis by a factor of 10.
(viii) Decreasing hysteresis by a factor of 10.
(ix) Increasing the system lag by a factor of 10.
(x) Decreasing system lag by a factor of 10.
(b) Explain your results.
Question 4. The purpose of the arrangement shown in FIGURE 4 is to mix the two liquid products A and B in a fixed mass ratio. Product A, which is itself a mixture, is a 'wild' flow, whilst product B, a pure compound, is controlled. As the mixture leaves the tank the transmitter ?TX measures its density.
(a) Complete the diagram to show how the arrangement could be controlled by the method of 'variable ratio control'.
(b) Identify which transmitter provides 'feedforward'.
(c) Describe how the control system responds to a disturbance caused by a variation in the density of product A.
![712_Control Systems And Automation8.jpg](https://secure.expertsmind.com/CMSImages/712_Control Systems And Automation8.jpg)
Question 5. FIGURE 5 shows a partially completed diagram of a flow control system. The flow controller is reverse acting and has a 0.2 to 1.0 bar pneumatic output signal which will supply both control valves V1 and V2.
The small range control valve, V2, only needs to operate on the first 25% output change of the controller output signal. For larger flow rates the small range valve will remain fully open and control will be achieved by operation of the large range valve. Note the differing air failure action of the two valves.
Design a system utilising valve positioners which will meet the prestated specifications.
Attachment:- Control Systems And Automation.rar
Overall perspective of the role of human resources
: Now that we are near the end, what is your overall perspective of the role of Human Resources? Do you think you will incorporate what you've learned in your pro
|
Important to our overall health
: Pick one of the purposes of our skin, hair, nails or glands and describe to why this is important to our overall health.
|
Managing director approach to the problem
: A public sector consultancy organisation recruited Mr. Alok, an expert in a particular field of technical specialisation with Ph.D. and other high qualification
|
Calculate the weighted average number of shares
: Assume that Cullumber Manufacturers had 1-for-10 reverse stock split instead of a 10% stock dividend on July 1,2020. Calculate weighted average number of shares
|
Describe how the control system responds
: Complete the diagram to show how the arrangement could be controlled by the method of 'variable ratio control' and Describe how the control system responds
|
Toward digital talent management
: Toward digital talent management please help me to propose additional resources (expertise, tools, software and hardware) and the time frame required to enable
|
Calculate the change in offset in the output produced
: Calculate the change in offset in the output produced by the step change and Draw a modified block diagram to show how the offset could be minimised
|
Explain the different classifications of accounts
: Explain the different classifications of accounts contained in the balance sheet and the income statement and the process for the income
|
Company talent management model
: Towards Digital Talent Management on Oil & Gas please help me to propose new HR practices by using SMAC (social, mobile, analytics, and cloud) technologies and
|