Derive an expression for the minimum radius and energy

Assignment Help Mechanical Engineering
Reference no: EM131467694

Question: 1. If the speed of an electron in the ground state of the Bohr model is uncertain by 1%, what is the uncertainty in position?

2. Using the Heisenberg uncertainty relation in the form pr = h ", derive an expression for the minimum radius r1 and energy E1 of a hydrogen atom.

Reference no: EM131467694

Questions Cloud

Create a new social media networking site : Try to remember the billboards on your commute to work or school. How many do you think there are?
Compare the value for the molar volume : Calculate and compare the value for the molar volume at 21.5 °C obtained in part 2 with the value for the molar volume at 21.5 °C obtained in part 1.
Computing the reduction potential : The reduction potential for Ni2+ is -0.247 V and for Co2+ is -0.277 V.
Should consumers trust companies : Should consumers trust companies? Why or why not? Do you think some consumers are just more prone to be loyal to companies .
Derive an expression for the minimum radius and energy : If the speed of an electron in the ground state of the Bohr model is uncertain by 1%, what is the uncertainty in position?
Location of the indicated substance after dialysis : Which of the following correctly describes the location of the indicated substance after dialysis?
Final volume of the sample of gas : What is the final volume of the sample of gas, if the pressure in the container is kept constant?
Energy are from the carbohydrate in the potato : A pasta side contains 20 grams of carbohydrate. If carbohydrate has a caloric value of 4 kcal/g, How many kcal or energy are from the carbohydrate in potato?
What kind of products are being sold? : What kind of products are being sold? Where did these products come from? For example - are there fresh vegetables and fruits?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assume that the crank has a solid circular cross section

Determine the maximum tensile, compressive, and shear stresses at points A and B on the bicycle pedal crank shown in the figure.

  Does this mean that f is a conservative force

Does this mean that F is a conservative force? Give reasons for your answer.

  Determine the maximum tensile stress in the laminated

a laminated thick-walled hydraulic cylinder was fabricated by shrink-fitting a steel e 200 gpa and v 0.30 jacket

  Dual cycle has a compression ratio

A Dual cycle has a compression ratio of 15:1. The state at the beginning of compression is 14.4psi and 60F. The volume ratio during the constant pressure part of the heat addition process is 2:1. The pressure ratio during the constant volume heat add..

  Determine the smallest force p that should be applied

Knowing that the coefficient of static friction is 0.30 at all surfaces of contact, determine the smallest force P that should be applied as shown to one of the wedges.

  Evaluate ordinates of the influence line at 6-ft intervals

Using moment distribution,construct the influence lines for the vertical reaction at support A and the moment in the beam at the face of the. wall) - Evaluate the ordinates of the influence line at 6-ft intervals.

  We now heat the water from a 200 c reservoir so the volume

water in a pistoncylinder is at 101 kpa 25 c and mass 0.5 kg. the piston rests on some stops and the pressure should be

  Determine the liquid height at the edge determine the

a 50 cm diameter 100 cm high cylindrical tank is partially filled with 50 cm high liquid with density 870 kgm3. the

  Heat transfer and work transfer for the two-step process

Ten pounds-mass of R-22 is at an initial volume of 4.059 ft3 and pressure of 200 psia. It is compressed isobaric ally until its volume is two-thirds of its initial volume. The piston is then held in place as the refrigerant cools until its temperatur..

  Derive analytical expression for temperature distribution

Derive an analytical expression for the temperature distribution along the length of the rod and for various time values.

  Determine the cooling load for july 30 at solar noon

The following table gives the characteristics of a building in Houston, TX. Determine the cooling load for July 30 at solar noon. Any information regarding the load not given may be assumed or neglected.

  The water at the constant pressure of 1 bar is

an electric water heater having 0.2 m3 capacity employs an electric heater to warm the water from 22degc to 55degc. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd