Cylinder fitted with a frictionless piston contains water

Assignment Help Mechanical Engineering
Reference no: EM13717356

A cylinder fitted with a frictionless piston contains water at 300 kPa and 200 degrees C, at which point the volume is 0.2 m^3. The piston is now moved slowly compressing the water to a pressure of 700 kPa. During this process PV^(0.9) = constant. Assuming that the room temperature is 20 degrees C, show that the process does not violate the second law, by evaluating the entropy produced.

Reference no: EM13717356

Questions Cloud

Cylinder fitted with a friction less piston contains water : A cylinder fitted with a frictionless piston contains water at 300 kpa and 200C, at which point the volume is 0.2 m^3. The piston is now moved slowly, compressing the water to a pressure of 700 kpa. During this process PV^0.9 = constant.
What is the magnitude of the force exerted on this particle : A particle with a charge of -1.85×10-8C is moving with an instantaneous velocity of magnitude 40.5km/s in the xy -plane at an angle of 50.5 degrees counterclockwise from the +x axis. What is the magnitude of the force exerted on this particle
How much mass has entered through the valve : An insulated piston cylinder assembly is attached through a valve to a source of air which is flowing through a pipe. initially, inside the cylinder the volume is 0.1 m^3, the temperature is 40C and the pressure is 1 bar. The valve is then opened to ..
What was the average speed while on the road : A trucker drove from san Francisco to Washington, dc (2865 mi). The entire trip required 77h and 30 min. What was the average speed while on the road
Cylinder fitted with a frictionless piston contains water : A cylinder fitted with a frictionless piston contains water at 300 kPa and 200 degrees C, at which point the volume is 0.2 m^3. The piston is now moved slowly compressing the water to a pressure of 700 kPa. During this process PV^(0.9) = constant.
Find the charge stored on given capacitor : Two capacitors, one 8.0 µF the other 16 µF, are connected in parallel across a 12-V battery. Find the charge stored on 16 µF capacitor
During an adiabatic process the pressure increased : A piston cylinder holds air at 80 degree F and 15 psi. During an adiabatic process the pressure increased to 165 psi and the entropy generated is 0.15 Btu/lb-degree R. Determine the isentropic efficiency for this
What is the maximum height of the pumpkin : A cannon fires a pumpkin at a 65 degree angle with an initial velocity of 15.0 m/s. What is the maximum height of the pumpkin
One-dimensional plane wall at a uniform initial temperature : Consider a one-dimensional plane wall at a uniform initial temperature Ti. The wall is 10 mm thick, and has a thermal diffusivity of 6 x 10^-7 m2/s. The left face is insulated, and suddenly the right face is lowered to a temperature Ts,r.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What must the humidity ratio and mass flow rate of the

an office is occupied by 30 persons who each produce 200 btuh 58w of sensible heat and 0.25 lbh 0.1kgh of moisture. the

  Maximum shear stress at the outer surface of the cylinder

A cylinder with a 0.3 m inner diameter and 0.4 m outer diameter is internally pressurized to 140 MPa. Determine the maximum shear stress at the outer surface of the cylinder.

  A 0018 cubic meter rigid tank is filled with saturated

a 0.018 cubic meter rigid tank is filled with saturated liquid water at 120c. a valve is opened until half of the mass

  A dragster starts from rest and has an acceleration

a dragster starts from rest and has an acceleration described by the graph. determine the time t for it to stop. also

  Coming out of a factory chimney are the following gases

coming out of a factory chimney are the following gases co2 so2 o2 n2 h2o with volume percentage to be 13.5 0.3 5.2 76

  A light truck weighs 3100 lb and is rated at 30 miles per

a light truck weighs 3100 lb and is rated at 30 miles per gallon for a 60 mph highway driving on level ground. how much

  Calculate drag force on flat bottom boat

Calculate drag force on flat bottom boat. What power is required to keep the boat moving at 0.5 m/s?

  The pressure inside a system varies inversely with the

the pressure inside a system varies inversely with the square of the system volume. determine work required to compress

  Determine the maximum allowable tensile load before

a 1 meter section of 1040 steel square tubing is loaded in tesnion. the tubing has an outer edge length of 10mm and a

  Fluid flow axially in annular region between two concentric

A fluid flow axially in the annular region between two concentric pipes with radii R1 and R2>R1, respectively. Assume the flow is steady, incompressible, axisymmetric, fully-developed, and has no swirl. Also neglect all body forces.

  Compute the speed of the person as a function theta for 0

in a contraption built by a fraternity a person sits at the center of a swinging platform with mass m 400kg and length

  Compare inlet steam mass and volume flow rates in pound mass

Compare the inlet steam mass and volume flow rates in pound mass per second and cubic feet per second of (a) a fossil-fuel power plant turbine having a polytropic efficiency of 0.90 and receiving steam at 2400 PSIA and 1000F and (b) a nuclear power p..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd