Cutting speed is 60mmin chip load is 025mmtooth and depth

Assignment Help Mechanical Engineering
Reference no: EM13629940

Explain the tapping operation and the steps to follow Peripheral milling is performed on the top surface of a rectangular work part that is 400mm long by 50mm wide. The milling cutter is 70mm in diameter and had five teeth. It overhangs the width of the part on both sides. Cutting speed is 60m/min, chip load is 0.25mm/tooth, and depth of cut is 6.50mm. Determine (a) machining time of the operations and (b) maximum material removal rate during the cut.

 

Reference no: EM13629940

Questions Cloud

A charged oil droplet falls 4 mm in 180 s at terminal : a charged oil droplet falls 4 mm in 18.0 s at terminal speed in the absence of an electric field. the specfic gravity
The unit cells of several orthorhombic crystals are : the unit cells of several orthorhombic crystals are described below. what is the bravais lattice of each and how do you
Calculate the energy of h2 molecule where nx ny nz - 10 : in general the quantization of transitional motion is insignificant for atoms because of their mass. however this
A tank whose volume is 001 m3 initially evacuated a pinhole : a tank whose volume is 0.01 m3 initially evacuated. a pinhole develops in the wall and the air from the surroundings at
Cutting speed is 60mmin chip load is 025mmtooth and depth : explain the tapping operation and the steps to follow peripheral milling is performed on the top surface of a
A feedwater heater extracts steam from a turbine at 600 : a feedwater heater extracts steam from a turbine at 600 kpa and 250degc which it combines with 0.3 kgs of liquid at 600
Consider an infinitely large homogeneous mixture of 235u : consider an infinitely large homogeneous mixture of 235u and a moderating material. determine the ratio of
Calculate the energy of h2 molecule where nx ny nz - 10 : in general the quantization of transitional motion is insignificant for atoms because of their mass. however this
A man pushes on a 60-lb crate with a force fthe force is : a man pushes on a 60-lb crate with a force f.the force is always directed down at a 30 degrees from the horizontal and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd