Create links between tasks and their predecessors

Assignment Help Mechanical Engineering
Reference no: EM131073710

Assignment:

This exercise begins with information for an IT Consultant Business Startup. Working in Microsoft Project, you will create the task list, including summary tasks and their sub-tasks, create links between tasks and their predecessors, add resources, and make changes to the original plan. Each student is required to submit their own, unique Project file.

A. Enter the tasks, including the specified duration, specified predecessors, and specified resources from the HW9DataFile. Make the Start date of the project: July 1, 2016.

B. Your business in charge of the IT Consultant Business Startup will be observing a week holiday for the week of the 4th of July and for the week of Labor Day. Be sure to enter the working exceptions for these holidays through the working time of the project, not through individual tasks or resources. After you make your corrections, identify the Original Finish Date for the entire project. Save the baseline at this point.

C. Your CEO feels the cost for the project to be excessive. Due to other projects planned, the CEO has asked for you to reduce the total cost for the project. The target budget for this operation is $55,000. Think carefully about the duration of the tasks and the resources required to make the project a success. Document the changes (ID number, task name, duration change, resource change, etc.) you plan on making to get the project under $55,000. Justify why you made the changes you did. Identify the new final cost of the project.

For your written response to B and C, submit a Word document. Remember to make your changes in response to C in the project.

Attachment:- datafile2.xls

Reference no: EM131073710

Questions Cloud

To what temperature will a dry object cool : The wind-chill index outside is -10 F when the wind blows at 20 mphand the air temperature is 20 F. To what temperature will a dry object cool when placed outside
Determine the forces at the four points : Measurements at the four points show deflections of .07, .12, .16, and .12 cm. Determine the forces at the four points.
Establishing wan links : What are the different technologies involved in establishing WAN links?
Dc analysis of transistor and dc load line : For the common emitter circuit shown below (see figure 1) the parameters are: VBB = 4 V, RB = 220 kΩ, RC = 2 kΩ, VCC = 10 V, VBE(on) = 0.7 V, and β = 200. Calculate the base current (IB), collector current (IC), emitter currents (IE), the VCEvoltage ..
Create links between tasks and their predecessors : This exercise begins with information for an IT Consultant Business Startup. Working in Microsoft Project, you will create the task list, including summary tasks and their sub-tasks, create links between tasks and their predecessors, add resources..
Understanding of package : List the differences between abstract and interface. Give me examples to demonstrate your understanding of package, abstract and interface.
Find the amplitude and period for trigonometric function : Find the amplitude, period, and phase shift for your trigonometric function and post a graph of at least one period
Determining the average salary : Write a query to return a list of department id's and average salaries where the depart-ment's average salary is greater than Ernst's salary.
Compare the economic vs managerial theory of firm : In a 3-4 page paper discuss, as well as compare and contrast the Economic Theory of the Firm vs the Managerial Theory of the Firm. Explain your understanding of how these two theories apply to the not-for-profit sector. You must use at least three..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  An adiabatic compressor compresses nitrogen

An adiabatic compressor compresses nitrogen (k=1.4, R=0.297) from P1=200 kPa and T1=300K to P2=1500kPa. The isentropic efficiency of the compressor is 80%, mass flow rate is 2247kg/hr, and I found T2s=533K and T2a=591K. How much power input does this..

  Problem 1 a 25 lbf block b is moving with a velocity vo of

problem 1 a 2.5 lbf block b is moving with a velocity vo of magnitude vo 6fts as it hits the 1.5 lbf sphere a which is

  What is the flow rate m3 of the gasoline and kerosene

crude oil is fractioned by two separating columns. the incoming crude oil is composed of the following weight fractions

  Transportation of old people

It is required to design the DC motor to run a small size electric vehicle to beused inside an airport building to help the transportation of old people.

  The fuel is consumed at a constant rate q dmdt and is

a rocket of initial mass m0 including shell and fuel is red vertically at time t 0. the fuel is consumed at a constant

  How far below the liquid level in the tank must the pump be

a feed rate of 200gpm of a hydrocarbon mixture at 70c is being pumped from tank at 1 atm abs pressure to a distillation

  Give examples of different materials used in different

materials are deep-seated in human culture. do you agree with this statement? why or why not? give examples of

  Membrane made of an isotropic material whose elastic modulus

There is a membrane made of an isotropic material whose elastic modulus and Poisson's ratio is E and v, respectively. When this membrane is elongated along x-direction with no lateral deformation in y-direction, the apparent elastic modulus (E') dete..

  Derive an expression for the compressibility of air

derive an expression for the compressibility of air represented by tau for 1 and isothermal process and 2 for an

  Determine the distance between a and b after 3 minutes

two ships a amp b are moving at constant velocities. at t0 the position of ship a is 2.41 miles east and 3.14 miles

  Determine the reaction force exerted by the nozzle

a curved nozzle assembly that discharges water to the atmosphere is shown. The nozzle mass is 4.5 kg and its internal volume is 0.002 m^3. The fluid is water. determine the reaction force exerted by the nozzle on the coupling to the inlet pipe.

  The drive roller for a conveyor belt a link a-b is rotating

the drive roller for a conveyor belt. a link a-b is rotating at 80 rpm counterclockwise .blink a-b is 60mm longlink b-c

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd