Create a primary function that uses a function handle with a

Assignment Help Civil Engineering
Reference no: EM13544466

1.What is the shear rate in the water between a sliding and standing plate, if V = 10 ft/s is the moving plate velocity and 0.1 in. is the distance between the plates? How much force is acting upon each in.^2 of either of the plates by the water? Will rate LIFESAVER if show work.

2.Create a primary function that uses a function handle with a nested function to compute the minimum of the function 20x2-200x+12 over the range 0<=x<=10.

Reference no: EM13544466

Questions Cloud

Write two command-line sockets programs : Write two command-line sockets programs – a client and a server – as follows. Define a Who-Am-I message as a UDP datagram containing the ASCII string “WHO AM I”
College and high school teaching similarities : College and High School teaching similarities are that he or she is put in a classroom to make sure that the rules are enforced and obey. ( how can I rephrase this sentence)
Loveliest of trees the cherry now : How can the poems, "Loveliest of Trees, the Cherry Now" and "High Windows" be compared and contrasted?
Identification of the major health issues for the african : Identification of the major health issues for the African American population with supporting evidence, data, and rationale
Create a primary function that uses a function handle with a : Create a primary function that uses a function handle with a nested function to compute the minimum of the function 20x2-200x+12 over the range 0
What are the values of its density specific volume : A certain gas weighs 16.0 N/m3 at a certain temperature and pressure. What are the values of its density, specific volume, and specific gravity relative to air weighing 12.0 N/m3 ?
Calculate the air mass temperature at the 1500 m. and 1000 : Consider a mass of air at 18 ºC, which is located at 1,000 m. above mean sea level. A strong wind moves the air mass over a mountain range at 2,500 m. mean sea level and then the air descends to an elevation of 500 m on the leeward
What is the percentage change in the specific volume : At a depth of 4 miles in the ocean the pressure is 9520 psi. Assume that the specific weight at the surface is 64.00 lb/ft^3 and that the average volume modulus is 320,000 psi for that pressure range.
What is its specific weight : If water vapor in the atmosphere has a partial pressure of 3500 Pa and the temperature is 30 degrees Celsius, what is its specific weight?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine corresponding increase in the diameter of vessel

a spherical pressure vessel has an outer diameter of 10 ft and a wall thickness of 0.5 in. knowing that for the steel used ?all= 12 ski, E= 29 x 10^6 psi, and v= 0.29, determine (a) the allowable gage pressure,

  Three different materials designated a b and c are tested

three different materials designated a b and c are tested in tension using test specimens having diameters of 0.755 in.

  What is the chlorine concentration when the tank is put back

A water tower containing 4000 m3 of water has been taken out of service to install a chlorine monitor. The concentration of chlorine in the water tower was 2.0 mg/L when the tower was taken out of service.

  Find what is the total force on the roof at collapse

a storage tank has a diameter of 80 ft, a height of 25ft and contains oil to a height of 15ft. the suction pumps, which can handle 15000bbl/d, are started, but the safety valves are clogged and a vacuum is drawn in the tank.

  How many holes are required to break 250000 tons

Conduct a powder factor design for the following conditions: -Rock is iron ore; density is 5370 lb/cubic yards -Rock swells 60% from in situ when broken -Bench height is 45ft -Drill hole diameter is 12.25 inches

  Determine the time at which the pressure in the tank

The velocity out of the tube may be approximated by V = √(2(p-patm)/ρ), where p is the absolute tank pressure. Determine the time at which the pressure (gage) in the tank is 20 kPa if the initial pressure is 40 kPa (gage)

  Determine the magnitude of the total acceleration at time t

Knowing that its speed continues to increase at the same rate until it reaches 100 km/h at point C, 1) determine the speed at point B, and 2) the magnitude of the total acceleration when t = 20 seconds.

  Calculate the size of an anaerobic digester required

Calculate the size of an anaerobic digester required to treat the sludge from a primary clarifier designed to treat 38,000 m3/d of sewage. The quantity of dry volatile solids removed by the plant is 0.15 kg dry solids/m3 sewage.

  To what rate of corrosion in mm per yr dose the correspond

A thick steel sheet of area 440cm3 is exposed to air near the ocean. After a one-year period it was found to experience a weight loss of 880g due to corrosion. To what rate of corrosion in mm/yr dose this correspond

  Determine the discharge in the channel in m3 per s

A very long rectangular channel connects two reservoirs and has a longitudinal slope of 0.005. The channel has a width of 10 m and a Manning's n of 0.030.

  Find what is the range of the values that would be expected

a spot speed study was conducted on a freeway on which the mean speed and the standard deviation were found to be 72 .4 mi/hr and 5.4 mi/hr, respectively. what is the range of the values that would be expected to contain the middle 95 percent of s..

  A fluid flowing in a pipe 30cm in diameter has a uniform

a fluid flowing in a pipe 30cm in diameter has a uniform velocity of 4ms. the pressure at the center of the pipe is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd