Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Create a MATLAB program and flowchart which will allow the user to input an unknown number of temperatures, each of which might be a temperature in Celsius, Fahrenheit, Kelvin, or Rankine, and will convert the user input temperature to each of the other temperature scales. The program should request the units of the input temperature from the user, accepting as the units the character ‘C', ‘F', ‘K', or ‘R'. The program will store the input and equivalent temperatures in vectors, using one vector for each temperature scale. Obviously, temperatures below absolute zero will not be inputs. The program will also determine the average temperatures on each scale. Output from the program will be a properly labeled table including: Temperature number (e.g., 1,2,3..), the temperature in C, F, K and R. In the last row of the table the program will output the average temperature for each scale. Do not use MATLAB vector commands (e.g. sum(X), mean(X), etc.). EXTRA CREDIT: Have the program check to make sure the entered ‘temperature unit' is valid (upper case ‘C', ‘F', R', or ‘K').
Water with a static pressure of 1.96kN/M 2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M 2 . How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/se..
The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..
What is the minimum distance from the stalled car at which the driver could apply the brakes and still stop before hitting it? Assume coefficient of rolling resistance of 0.013.
What is the salt usage for each regeneration if the system regenerated every 10 days? What size resin tanks (diameter, height) would be required for a duplex system with no redundancy?
Calculate average figures for tonnes/round and powder factors in kg/tonne and Determine the drill metres required to achieve a production rate from grade control blasting.
The section of the plywood in the 3rd quadrant is sawed off and the resulting piece is then glued squarely over the 4th quadrant portion of the plywood with glue of negligible weight.What are the x- and y-coordinates of the resulting center of gra..
The posItIon of a particle along a straight line is given by s = (t 3 - 9t 2 + 1St) ft, where t is in seconds. Determine its maximum acceleration and maximum velocity during the time interval 0 :5: t :5: 10 s.
To satisfy desige limitation it is necessary to determine the effect of the 2- kN tension in the cable on the shear tension and bending of the fixed I-beam.
Estimate the effective friction angle for the sand (assume c' = 0). Calculate the sand's shear strength (τf) on a horizontal plane at depths of the 20 ft and 50 ft.
A soil borrow material in its natural state in the ground has a unit weight of 118pcf. Its natural water content is 7%. What is the dry unit weight of this material?
Two strips of a plastics material are bonded together as shown. The average shearing stress in the glue must be limited to 1000 kpa.
a) The maximum flow rate that can be achieved without cavitation occurring in the piping system. b) The maximum elevation of the highest point of the piping system to avoid cavitation.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd