Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. Create 8 bit subtractor in Verilog that uses a 8-bit adder Write a test bench that will test the code with 2 sets of numbers made up of the ASCII Values of the first 2 letters of your first name and the first 2 letters of your last name as the 2 sets of & bit numbers. In each case subtract the 1st letter from the second letter in the test bench and use the $dispLay command to print the results and paste in a screen shot and the code.
2. Write Verilog code for a module called JKFF(JK Flip Flop) that has inputs J, K ClrN, SetN, ClK and outputs Q and QN. Make the gja asynchronous Write a test bench to simulate all combinations of J and K for the single FF. Then create a module that uses 4 instantiations of the JKFF to create a register that can hold 4 bits, but do not write test bench for the 4 bits. Submit code and test bench code.
Typically, a speech signal that can be understood over a telephone shows frequencies from about 100 Hz to about 5 KHz. What would the sampling frequency fs (samples/ sec) that would be used to sample a speech without aliasing
In a certain system, an electrical heating element was found to increase the temperature of a piece of metal 7o for each amp of current. The metal expands 0.004 in./deg and pushes on a load sensor that outputs 1 V/0.003 in.
How Automatic UPS system wiring circuit diagram for Home or Office works in both cases when the supply is available and when its not .
Let y(t) he the signal at the output of the LTI system when x(t) is the input signal. The following signals are sampled using a train of impulses with periodicity T, signal x(t) is sampled to obtain xc(t), and signal y(t) is sampled to obtain yc(t..
An induction motor has the following specifications: a 8-polesquirrel cage rotor, operates at 25 hp off of a 220 V line-to-line3-phase service, 60 Hz, 64 amps of line current, and under fullload runs at 830 RPM. The motor draws 20.8 kW at full loa..
A coaxial cable has a loss of 5.6 dB at a frequency f. A signal at f has ans rms amplitude of 1.7 mV at the cable input. What is the rms amplitude after it has traveled the length of the cable
What is the minimum donor doping required to convert Silicon into a conductor? What is the minimum acceptor doping required to convert Silicon into a conductor?
Two positive charges of 250 microcoulombs each are 20cm apart. Determine the electric potential halfway between them.
Investigate and produce a report on the main different logic families and their requirements - Describe with the use of circuit diagrams the difference between TTL (74 series) and CMOS (4000) integrated circuits.
A 250V rms system is supplying three parallel loads. One draws a 20kW at unity power factor, a second uses 25kVA at PF=.8 lagging, and the third requires a power of 30kW at a lagging PF of.75
Although this forms PNP and NPN transistors, the bias of the regions isdesigned so the junctions are reverse biased and the electric fieldeffects on the channel are supposed to control the MOS-FETtransistors operations.
A d-c voltage Vo is applied att = 0 directly to the input terminals of a lossless air dielectric transmission line of length l. The line has a characteristice resistance Ro and is terminated in a load resistanceRL =2Ro.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd