Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Given the image data "cruiseorg.tiff", perform JPEG compression by completing the following steps:
a. Convert the image to gray scale.
b. Write a MATLAB program for encoding with the following features: (1) divide the image into 8× 8 blocks; (2) transform each block using the discrete-cosine transform; (3) scale and round DCT coefficients with the standard quality factor. Note that using lossless compression with the quantized DCT coefficients is omitted here for a simple simulation.
c. Continue and write a MATLAB program for decoding with the following features: (1) invert the scaling process for quantized DCT coefficients; (2) perform the inverse DCT for each 8× 8 image block; (3) recover the image.
d. Run the developed MATLAB program to examine the image quality using
Why the reactance of a system under fault condition is low and faults currents may raise dangerously high value. ?
Design a two-way radio link to operate over earth-Mars distances for data and picture transmission with a Mars probe at 2.5Ghz with a 5-MHz bandwidth. A power of10-19 W Hz-1 is to be delivered to the earth receiver and 10-17 WHz-1 to the Mars rece..
A specific type of MOSFET has VT = -1 V. The MOSFET is in the ON state (a short exists between its drain and source) when vGS ≥ VT. The MOSFET is in the OFF state (an open circuit exists between its drain and source) when vGS
1. What does "transfer function" of a filter represent 2. What do the Amplitude Ratio (Gain) and Phase Angle represent 3. What are the key differences between a real filter (the RC circuit) and an Ideal Filter (please read LPF Treated as an Ideal F..
A 60 Hz, three-phase, transposed transmission line has the following parameters: Z = 13.114+ j52.952, Y = j0.311/1000. The sending-end line-to-line voltage is 161 kV. The total receiving-end load is represented by ZL =143 with an angle
Consider a digital filter with frequency response: H(f)=11+f Assuming the sampling frequency is 1500Hz what is the frequency attenuation of a signal passing through this filter at 280Hz
For what range of values of a is the system stable?
Characteristics of a filter, A filter has the following characteristics: Attenuation = 3.0 dB from 0 Hz to 2 kHz. From 2 kHz to 20 kHz attenuation increases from 3 dB to 23 dB in a straight line when plotted on axes of power in decibels (vertical a..
Usually, transformers are designed to operate with peak flux densities just below saturation of the core material. Why would we not want to design them to operate far below the saturation point? Far above the saturation point? Assume that the vol..
An unknown semiconductor has a bandgap of 1.1eV and Nc = Nv. It is doped with 10^15 cm-3 donors where the donors fully ionized. Given that EF is 0.25 eV below Ec, calculate the concentration of electrons and holes in the semiconductor at 300 K and..
design an IIR high-pass filter using bilinear method in a system with sampling frequency of 100 Hz. The lower and higher cutoff frequencies are at 18 Hz and 35 Hz respectively. Pre-warp the cutoff frequencies.
How many turns of wire are required to produce a B-field whosemagnitude is greater than or equal to 10-3[T] inside anair-wound solenoid that is 2 [cm] long and carries a current of 100[mA].
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd