Construct the truth table to evaluate the effect of each

Assignment Help Mechanical Engineering
Reference no: EM13632773

The pump motor control relay is controlled by the following sensors:

A: Position sensor to sense if the train car is in position. This sensor is a normally closed optical sensor.

B: Limit switch in the holding tank to sense whether there is enough fuel

to fill a tanker car. This switch is a normally open sensor.

C: Limit switch on the filler tube nozzle to sense whether the fuel level in the tanker is at the proper level (tanker is filled). This switch is a normally open sensor

CR: The pump motor control relay (CR), which functions as normally open.

An emergency stop button (neglect this is your design for simplicity).

The pump motor should turn on when the tanker is in position and there is a proper amount of fuel in the holding tank. The pump motor should turn off when the proper fuel level is reached in the tanker or the emergency stop is pushed (neglect the e-stop for this example).

1. Construct the truth table to evaluate the effect of each set of input conditions on the output (pump motor control relay).

2. Convert the truth table into a Boolean expression. Simplify the expression.

3. Draw the ladder logic rung to control the control relay for the pump motor.

Reference no: EM13632773

Questions Cloud

Iq data is thought to be normally distributed with a mean : iq data is thought to be normally distributed with a mean of 100 and a standard deviation of 15. using the emperical
After your calculations explain two practical strategies : calculate the cost per piece of a milling operation that is used to machine a pocket of 2x3x0.5 lxwxd. the material
Suppose you pay 200 for a raffle ticket for local : suppose you pay 2.00 for a raffle ticket for local organization raising money. the single winner recieves a 75home
State the final form and the constants of the controller : 1.find an example of a feedback control system from suggested textbooks. some of the examples can be given belowbulldc
Construct the truth table to evaluate the effect of each : the pump motor control relay is controlled by the following sensorsa position sensor to sense if the train car is in
What mass of sand grains would have a total surface area : grains of fine california beach sand are approximately spheres with an average radius of 50 mum and are made of silicon
Suppose you were given the task of estimating the : suppose you were given the task of estimating the proportion of drivers in troy al who text while they drive. discuss
If a couple consists of a non-albino and an albino what is : genes related to albinism are denoted by a non-albino and a albino. each person has two genes. people with aa aa or aa
Air is compressed in a steady-flow compressor via a : air is compressed in a steady-flow compressor via a polytropic process from 15 psia and 60ordmf state 1 to 75 psia and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd