Considering the ammonia as a system

Assignment Help Mechanical Engineering
Reference no: EM13708106

A certain balloon is constructed of a material such that the pressure inside is related to the volume according to the relation PV^(-2/3)=constant. The balloon contains 2kg of ammonia initially at 0C, 60% quality. The balloon is now heated until the final pressure inside reaches 600 kPa. Considering the ammonia as a system, how much work in kJ, is done during the process?

Reference no: EM13708106

Questions Cloud

Compute the frictional losses between these two sections : Water flows in a 2 ft diameter duct under the following conditions: p1= 55 psia and v1=20ft/sec. At another section 12 ft below the first the diameter is 1 ft and the pressure p2=40 psia. Compute the frictional losses between these two sections. Dete..
Piston-cylinder assembly contains a two-phase liquid-vapor : A piston-cylinder assembly contains a two-phase liquid-vapor mixture of ammonia initially at 500 kPa with a quality of 98%. Expansion occurs to a state where the pressure is 150 kPa. During the process the pressure and specific volume are related by ..
Calculate the volume flow rate and mass flow rate : Water at 30 degrees C flows through a horizontal pipe (1 inch inside diameter), in which the pressure drop is to be limited to 0.015 lbf/ft^2 per foot of length. This low pressure per foot is imposed by the excessively long line involved. Calculate t..
What is the stagnation temperature at the outlet : The following information is known about the steady flow of methane through a horizontal insulated duct: Determine the outlet velocity. What is the stagnation temperature at the outlet?
Considering the ammonia as a system : A certain balloon is constructed of a material such that the pressure inside is related to the volume according to the relation PV^(-2/3)=constant. The balloon contains 2kg of ammonia initially at 0C, 60% quality. The balloon is now heated until the ..
A cantilevered beam with a rectangular cross section : A cantilevered beam with a rectangular cross section is loaded by a force perpendicular to the beam center line at the free end. The cross section is 100mm high and 25mm wide. The vertical load at the beam end is 40,000N.
Temperature change of water as it flows through the duct : Water flows through a duct of varying area. The difference in stagnation pressures between two sections is 4.5 x 10^5 N/M^2. If the water remains at a constant temp, how much heat will be transferred in this length of duct? If the system is perfectly..
Opened and half of the mass of the gas is allowed to escape : A rigid tank contains 5.56 kg of an ideal gas at 3.6 ATM and 40 degrees Celsius. Now a valve is opened and half of the mass of the gas is allowed to escape. If the final pressure in the tank is 2.0 ATM, the final temperature of the tank is?
Contained in a cylinder fitted with a piston : Argon gas initially at 140 kPa, 10C is contained in a cylinder fitted with a piston. The initial volume of the gas is 0.2m^3. The gas is now compressed in a poly tropic process, PV^(1.4)=constant, to a final pressure of 700 kPa assuming ideal gas beh..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assuming no change in the kinetic or potential energy of

a centrifugal compressor used in a gas turbine engine increases the pressure of 2000 lbmmin of air from 15 psia to 150

  Determine the minimum annual operating cost of a heat

providing domestic hot water to a household typically requires 107 kj of energy per year. a typical electric water

  Which is perfectly flexible infinitely strong and

a 10 gram mass is attached to the end of a 2 meter string which is perfectly flexible infinitely strong and weightless.

  Te point starts moving at t0 find the total distance

the position of a point p on a line is given by the equation x t sinpi t2. the point starts moving at t0. find the

  Consider no change in heat transfer kinetic and potential

consider a steam turbine in which the steam enters at 23.26 mpa and 808 k with a flow rate of 17.78 kgs. the steam

  Discuss how the steam power plant steam engine rankine

discuss how the steam power plant steam engine rankine cycle can control the speed of the vehicle during acceleration

  The acme company claims to have designed an adiabatic

the acme company claims to have designed an adiabatic turbine that will produce 105btu per pound of steam. the

  Determine the maximum velocity reached

A 0.7-lb block rests on top of a 0.5-lb block supported by but not attached to a spring of constant 9 lb/ft. The upper block is suddenly removed. Determine (a) the Maximum velocity reached by the 0.5-lb block, (b) the maximum height reached by the..

  Determine the acceleration of the particle

The motion of a particle in defined by the relation x = t3 - 15 t2 - 20, where ‘x' is expressed in metres and ‘t' in seconds. Determine the acceleration of the particle at t = 3 seconds.

  For problem 372 in meriam and kraiges 6th edition dynamics

for problem 372 in meriam and kraiges 6th edition dynamics why is the max normal force at the side? how can we prove

  Aircraft executes horizontal turn at constant true air speed

In a correctly banked turn of radius R, an aircraft executes a horizontal turn at constant true air speed, V, with no sideslip and zero roll rates. The aircraft must bank at an angle phi from the horizontal so that the horizontal component of its lif..

  Determine the initial tension in the cord

The spool has a mass of 75 kg and a radius of gyration . It rests on the inclined surface for which the coefficient of kinetic friction is . If the spool is released from rest and slips at A, determine the initial tension in the cord and the angul..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd