Consider an ocean thermal energy conversion power plant in

Assignment Help Mechanical Engineering
Reference no: EM13629323

Consider an ocean thermal energy conversion power plant in Hawaii designed to operate between temperature limits of 90°F (ocean surface) and 40°F (deep ocean). Cold water of density 64 lbm/ft3 is pumped at the rate of 13,300 gallons per minute from deep ocean and heat is rejected to this water causing its temperature to increase by 6°F. The power plant produces 415 hp of electricity.

(a) Calculate thermal efficiency (%) of the power plant.

(b) Is the Carnot principle violated? Provide quantitative justification.

Reference no: EM13629323

Questions Cloud

Nickel has a fcc crystal structure and 0125 nm atomic : nickel has a fcc crystal structure and 0.125 nm atomic radius. draw two nearest parallel 110 planes in a fcc crystal
Air enters a set of these nozzles at 215 psia and 700 : the stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically.
Steam expands isentropically from 2 mpa and 500 k to a : steam expands isentropically from 2 mpa and 500 k to a final state in which the quality is 0.90. determine the final
The weights of ripe watermelons grown at mr smiths farm are : the weights of ripe watermelons grown at mr. smiths farm are normally distributed with a standard deviation of 2.9 lb.
Consider an ocean thermal energy conversion power plant in : consider an ocean thermal energy conversion power plant in hawaii designed to operate between temperature limits of
The power output of an adiabatic steam turbine is 55 mw at : the power output of an adiabatic steam turbine is 5.5 mw. at the inlet p 2.0 mpa and t 435 degc. the steam enters the
If you are told that a variable follows a normal : 1.if the time it takes to finish a quiz follows a uniform distribution between 0 and 4 minutes what is the probability
How many electrons should be removed from an initially : how many electrons should be removed from an initially uncharged spherical conductor of radius 0.200 m to produce a
Find the elapsed time to vaporize the propane and total : a factory has a large liquid propane storage tank. the propane is to be used as vapor. evaporation of the liquid

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd