Reference no: EM13720673
In the large scale manufacturing of Jaguar Bold Blue Bouncy Balls (JB4) for children, it is important that their material properties be sufficiently uniform. One way to detect gross differences in their material properties is to observe how a ball rebounds when dropped on a hard strike plate (see the figure below). Assuming that each ball has a radius R of 23.0 mm, design a sorting device to select the balls with 0.900 < e < 0.925, where e is the coefficient of restitution, which is sometimes written as COR. These balls have a density of 0.95 g/cm3. The device consists of an incline defined by the angle and length L. The strike plate is placed at the bottom of a well with depth h and width w2. Finally, at a distance w1 from the end of the incline, there is a trap with a diameter d. By releasing a ball from rest at the top of the incline and assuming that the ball slides with negligible friction, the ball will reach the bottom of the incline with a speed v0, rebound off the strike plate, and then fall directly in the trap.
In your design, choose appropriate values of L, ?, h, w1, w2, and d to accomplish the desired task while ensuring that the overall dimensions of the device do not exceed 2.0 meter in both the horizontal and vertical directions. The values for inclined angle should not exceed 45°.
It is not absolutely necessary for this stage of the design, but you may want to:
• Consider adding a design element that prevents balls from simply rolling into the trap if the actual trajectory doesn’t match the desired trajectory.
• Allow your analysis to handle a different radius (R) value for the ball.
Calculate the entropy change of the two reservoirs
: Heat in the amount of 100 kJ is transferred directly from a hot reservoir at 1200 K to a reservoir at 600 K. Calculate the entropy change of the two reservoirs and determine if the increase of entropy principle is satisfied.
|
What is the minimum temperature rise possible
: Air at 14.7 psia and 70 degrees Fahrenheit is compressed adiabatically by a centrifugal compressor to a pressure of 100 psia. What is the minimum temperature rise possible? Explain.
|
Dimensional wall of material
: A one dimensional wall of material (Kw=10w/mk) is 50 mm thick with uniform heat generation q‘‘‘=5*10^6w/m^3. The left side is exposed to a fluid hl=500w/m^2k at 20 degree Celsius. The right side has a 10mm thick plate attached that has no heat genera..
|
Saturated liquid water is compressed
: Saturated liquid water is compressed from 100 kPa (State 1) to 2.5 MPa (State 2) in an adiabatic pump having 85% isentropic efficiency. Calculate the specific work (kJ/kg) required for the compression of liquid water. Determine the entropy generation..
|
Consider adding a design element that prevents balls
: In the large scale manufacturing of Jaguar Bold Blue Bouncy Balls (JB4) for children, it is important that their material properties be sufficiently uniform. One way to detect gross differences in their material properties is to observe how a ball re..
|
Calculate the potential emissions of toluene
: A stream of gas flowing at 15,000 scfm contains 20 ppm of toluene. Assuming the process operates 8500 hours per year, calculate the potential emissions of toluene, tons/year. What kind of a system should be considered to control this stream, and why?
|
Estimate the concentration and the mass emission rate
: Estimate the concentration (in ppm) and the mass emission rate of NOx (in kg/hr, expressed as NO) if a coal containing 1.5% nitrogen is combusted at 1400 K using an air/fuel ratio that is 1.5 times the stoichiometric ratio.
|
Coal-fired power plant is burning coal with a heating value
: A 500 MW coal-fired power plant is burning coal with a heating value of 12,000 Btu/lb. The coal contains 2.0% sulphur. The plant has a thermal efficiency of 38%, and uses an air/fuel ratio of 14:1 (mass basis).
|
Calculate the required control efficiency
: An alcohol manufacturing facility emits air with 500 ppm ethanol. The air flows out several roof vents at a total flow rate of 1000 m³/min (at 25 ° C and 1 atm). The facility is required to collect all the vented air and route it to a bio filter to c..
|