Consider a steam power plant that operates on a

Assignment Help Mechanical Engineering
Reference no: EM13631200

Consider a steam power plant that operates on a regenerative ranking cycle and has a net power output of 150MW .steam entersvthe turbine at 10Mpa and 500 degrees celsuis and the condenser at 10Kpa . The isentropic efficiency of the turbine is 80% and that of the pumps is 95% . Steam is extracted from the turbine at 0.5Mpa to heat the feed water in an open feed water heater.water leaves the feed water heater as a saturated liquid. Determine the mass flow rate of steam through the boiler and the thermal efficiency of the cycle .

Reference no: EM13631200

Questions Cloud

Stray heat transfer from the heat exchanger may be : consider an air-water heat exchanger. air flowing steadily at the rate of 0.5 kgs enters the heat exchanger at 100 kpa
Two forces p and q are applied as shown at point a of a : two forces p and q are applied as shown at point a of a hook support knowing that p 15n and q 25n determine
A 0210-a current is charging a capacitor that has circular : a 0.210-a current is charging a capacitor that has circular plates 15.8 cm in radius. the plate separation is 4.00 mm.a
A hair dryer consumes 1200w of electric power when running : a hair dryer consumes 1200w of electric power when running the inlet volume flow rate and the exit velocity of air are
Consider a steam power plant that operates on a : consider a steam power plant that operates on a regenerative ranking cycle and has a net power output of 150mw .steam
A compressor is used to bring saturated water vapor at 150 : a compressor is used to bring saturated water vapor at 150 lbfin2 up to 2500 lbfin2 where the actual exit temperature
The turbine exit pressure is 10kpa the overall efficiency : a geothermal power plant is supplied with water at a well bottom temperature of 225 degrees c and a pressure of 8 mpa.
The viscoelastic response of a common orthopedic polymer is : the viscoelastic response of a common orthopedic polymer is represented using a maxwell model so that the spring
Calculate first the temperature at the center of one face : a cube of aluminum 10 cm on each side is initially at a temperature of 300degc and is immersed in a fluid at 100degc.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain the following terms with respect to 4-storke cycle

explain the following terms with respect to 4-storke cycle internal combustion engines strokebore ratio piston

  Calculate the work done when a gas expands from 350kpa and

during some actual expansion and compression processes in piston-cylinder devices the gases have been observed to

  If the turbine is 90 percent efficient how much energy can

a turbine is designed to extract energy from a water source flowing through a 10 cm diameter pipe at a pressure of 800

  Consider the figure below which shows the energy-band

question 1consider the figure below which shows the energy-band splitting of silicon. if the equilibrium lattice

  The performance of a device is defined as the ratio of the

the performance of a device is defined as the ratio of the desired output to the required input and this definition can

  If the velocity of a 1 id pipe is determined to be 02 fts

if the velocity of a 1 id pipe is determined to be 0.2 fts by a transit time flow meter what if the volume flow rate?

  An air-standard otto cycle operates with a compression

an air-standard otto cycle operates with a compression ratio of 8. at the start of the compression stroke the pressure

  Explain why this is consistent with our definition of

show that the circumferential strain measured by a transverse gage on a round bar is the same as the radial strain.

  What is the angular acceleration of the disk for this value

when a disk rolls on a surface without slip the velocity of the point of contact of the disk with the surface is zero

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  What constant speed increase is needed for the total

a car at point a is 100m away from point b along a circular track distance measured along the tracks perimeter and

  A remote sensing satellite is deployed in a circular

a remote sensing satellite is deployed in a circular sun-synchronous orbit with inclination 96.85deg. a. calculate

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd