Consider a regenerative vapor power cycle with two

Assignment Help Mechanical Engineering
Reference no: EM13628523

Consider a regenerative vapor power cycle with two feedwater heaters, a closed one and an open one. Steam enters the first turbine stage at 80 bar, 480°C, and expands to 20 bar. Some steam is extracted at 20 bar and fed to the closed feedwater heater. The remainder
expands through the second turbine stage to 3 bar, where an additional amount is extracted and fed into the open feedwater heater, which operates at 3 bar. The steam expanding through the third turbine stage exits at the condenser pressure of 0.08 bar. Feedwater leaves the closed heater at 205°C, 80 bar, and condensate exiting as saturated liquid at 20 bar is trapped (throttled) into the open heater. Saturated liquid at 3 bar leaves the open feedwater heater. The net power output of the cycle is 100MW. If the turbine stages and pumps are isentropic, draw cycle on a T-S diagram and determine

a) The thermal efficiency of the cycle

b) The mass flow rate of steam entering the first turbine in kg/h

Reference no: EM13628523

Questions Cloud

A uniform electric field aibj intersects a surface of area : a uniform electric field aibj intersects a surface of area a. what is the flux through this area if the surface lies
Compression is isentropic to the condenser pressure of : the following figure shows the schematic diagram of a vapor compression refrigeration system using r-134a as the
A 350 cm diameter loop is rotated in a uniform electric : a 35.0 cm diameter loop is rotated in a uniform electric field until the position of maximum electric flux is found.
Determine the resultant lift force p that this wing : the wing is supported by a strut be with ball-and-socket joints at b and e and by bearings at a and f. the bearings
Consider a regenerative vapor power cycle with two : consider a regenerative vapor power cycle with two feedwater heaters a closed one and an open one. steam enters the
Write all the necessary boundary conditions to determine : consider a solid cylinder of radius r and height h. heat is generated in the solid at a uniform rate of q wm3. one of
To the dismay of scientists on earth an electrical fault : an unmanned spacecraft is in a circular orbit around the moon observing the lunar surface from an altitude of 49.0km .
As the airplane begins its takeoff run at t 0 the normal : as the airplane begins its takeoff run at t 0. the normal forces exerted on its tires at a and b are na 4.2 kn and nb
In a recent survey 45 indicated chocolate was their : in a recent survey 45 indicated chocolate was their favorite flavor of ice cream. suppose we select a sample of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd