Consider a piston-cylinder system with an initial volume

Assignment Help Mechanical Engineering
Reference no: EM13703801

Consider a piston-cylinder system with an initial volume of 0.04 m3 at 200 kPa. Calculate the work being carried out to increase the volume to 0.1 m3 for each of the following processes (drawing diagrams P - V for each case):

a) A burner is placed and the volume increases at constant pressure

b) The weights are removed so that PV = constant

c) The weights are removed so that PV1.3 = constant

d) It cools at constant volume until a pressure of 100 KPa.

Reference no: EM13703801

Questions Cloud

Temperature of refrigerant at end of the heating process : A rigid tank is heated for 9 minutes with a 800W electrical heater. During this time 70kJ of energy is lost due to heat transfer to the environment. Find the temperature of the refrigerant at the end of the heating process.
Determine the rate of evaporation of water : Water is boiled at sea level (1 atm pressure) in a pan placed on top of a 2-kW electric burner that transfers 60% of the heat generated to the water. Determine the rate of evaporation of water in kg/s.
What is the smallest allowable length of the robot arm : A robot arm carrying a 2.75-lb package is moving in a horizontal circle at 4 miles/hr. The arm is gradually shortened for the first 0.11 s of its motion, changing the radius of the circle. The maximum acceleration the package can withstand without da..
Air-an ideal gas is isentropic ally compressed : Air, an ideal gas, is isentropic ally compressed from V1 = .36 ft^3, P1 = 14.5 psia, T1 = 70 F, to V2 = .03 ft^3 (compression ratio = 12). Find T2, P2 and W (work in Btu) for this process:
Consider a piston-cylinder system with an initial volume : Consider a piston-cylinder system with an initial volume of 0.04 m3 at 200 kPa. Calculate the work being carried out to increase the volume to 0.1 m3 for each of the following processes
How many nmi would airplane be off from the original target : An airplane flying at 185 kts with heading 320? Towards a target 300 nmi (nautical miles) away, experiences a steady wind of 23 kts from 020? If the time, without wind, to fly to the target was t.
Determine frequency range for which amplitude dynamic error : A pressure transducer has a damping ratio of 0.3 and a natural frequency of 12,000 Hz. Determine the frequency range for which the amplitude dynamic error will be less than 10 percent.
A particle travels along a straight line with a velocity : A particle travels along a straight line with a velocity of v=(4t-3t^2)m/s, where t is in seconds. Determine the position of the particle when t = 3.5s .s=0 when t=0. A sphere is fired downwards into a medium with an initial speed of 28m/s .If it exp..
Monopolist do to maximize profits : A pure monopolist determines that at the current level of output the marginal cost of production is $2.00, average variable costs are $2.75, and average total costs are $2.95. The marginal revenue is $2.75. What would you recommend that the monopolis..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate uncertainty in resistance of resultant circuits

Two resistors, R 1 = 100.0 ± 0.2 ? and R2 = 50.0 ± 0.1 ?, are connected (a) in series and (b) in parallel. Calculate the uncertainty in the resistance of the resultant circuits. What is the maximum possible error in each case?

  Determine the natural frequencies of the system

Determine the natural frequencies of the system. For the baseline system I get natural frequencies at the following engine speeds: 435, 2026, 2818, 5225, 7093, 10245, and 12153 rpm.

  Consider an ideal gas-turbine cycle with two stages of

consider an ideal gas-turbine cycle with two stages of compression and two stages of expansion. the pressure ratio

  What is the pressure at the bottom of the mariana trench at

a sea water is often modeled as an incompressible fluid with a density of 1025 kgm3.what is the pressure at the bottom

  Determine the total mechanical energy of the river water

consider a river flowing toward a lake at an average velocity of 3 ms at a rate of 500 m3s at a location 90 m above the

  Calculate the force required to push liquid oil

Calculate the force required to push liquid oil, with the density of 890 kg/m^3, through a 1 mm diameter hole. Account for viscous forces and please show all work.

  Show how did you do the maintenance during your workshop

show how did you do the maintenance during your workshop machines were sent to your workshop from a big

  After exiting the turbine the water is then reheated at 4

water as steam enters an adiabatic turbine at 6 mpa and 600 c with a flow rate of 5 kgs. after exiting the turbine the

  The wire stretches 45mm when a tensile force p is

an 18-m long steel wire of 5mm diameter is to be used in the manufacture of a presstressed concrete beam.it is observed

  With all similarity conditions satisfied the measured drag

the drag on a 2-m-diameter satellite dish due to an 80-kmhr wind is to be determined through a wind tunnel test using a

  A composite wasll is to be constructed of 14 inch stainless

a composite wasll is to be constructed of 14 inch stainless steel k10.5 buthr-ft-degrees f 3.0 inches of corkboard

  Consider a counter-flow heat exchanger in a refrigeration

consider a counter-flow heat exchanger in a refrigeration system. saturated liquid-vapor mixture of r-22 enters the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd