Consider a mixing chamber into which cold air enters

Assignment Help Mechanical Engineering
Reference no: EM13711593

An air-conditioning system, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8C and 100 kPa at a rate of 0.55 m^3 /s and warm air enters at 300C and 100 kPa. The ratio of mass flow rates of warm to cold air streams is 1.6. Using variable specific heats, determine the mixture temperature leaving the mixing chamber.

Reference no: EM13711593

Questions Cloud

Briefly explain how gmos are created : Briefly explain how GMOs are created in your own words.
Fire truck draws water from an open constant-level reservoir : A fire truck draws water from an open constant-level reservoir through a hose of 0.2 ft2 cross section. The water is discharged from the pump through another 0.2 ft2 hose to a surge tank pressurized to 120 psig with air at the top. The pump adds 970 ..
Determine volume and height of cooling tower-effectiveness : A counter flow cooling tower cools 2000 gal/min water from 104 F to 85 F with 210,000 ft^3/min of air at 90 F Dry bulb Temperature and 76 F WBT . The Mass transfer coefficient -surface area product is hA= 123lbm/hr ft^3. Air mass flow rate per unit c..
Strained juice is concentrated in a vacuum evaporator : In a process for concentrating 1000kg of freshly extracted orange juice containing 12.5 wt% solids, the juice is strained, yielding 800kg of strained juice and 200kg of pulpy juice. The strained juice is concentrated in a vacuum evaporator to give an..
Consider a mixing chamber into which cold air enters : An air-conditioning system, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8C and 100 kPa at a rate of 0.55 m^3 /s and warm air enters at 300C and 100 kPa. The rat..
What statistical method can you apply using this data : What statistical method can you apply using this data?
The temperature and pressure when the exhaust valve opens : A 4 cylinder 1.6 liter SI engine has a compression ratio of 10, connecting rod length of 16.8cm, and a crank offset of 4.5 cm. The engine is operating at 3000 RPM and wide open throttle. The exhaust pressure is 100 kPa. The intake valve closes at 20 ..
Advantage of using electric chiller and gas-fired chillers : What’s the C.O.P. for a 5-ton of gas fired (absorption) chiller uses 15 kw electric and 5 thermo gas? What would be the advantage of using electric chiller and gas-fired chillers in combination? How would you sequence their operations? How much chill..
Determine the temperature drop during this process : Refrigerant-134a is throttled from saturated liquid state at 7 bar to a pressure of 1.4 bar. Determine the temperature drop during this process and the final specific volume.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd